Official 330 Sundancer Thread

Hi All
I am looking to replace my cockpit carpets and would like to hear from anyone who has replaced their carpet with any of the faux teak deck type materials and if so where you got it from.
 
domer94 said:
yes , I put in the three bank / 2 alt isolator which ties in the alternators to all three banks. as for a/c load for the inverter, I would probably only be using TV / dvd and occasional microwave / blender. although I do have dual voltage tv , they are all plugged into the ac outlet in that compartment.
Click to expand...

That dual-voltage TV will always run off the inverter as long as it is supplying power. This is less efficient than running the TV directly from DC. Twe're it me, I'd set it up such that the TV always runs off DC.
 
Recently bought new canvas for my ‘98 330 Sundancer. Had to buy all the pieces so they would match. Therefore I have a Bimini and sunshade in pretty good shape. “Toasted Tweed” if anyone is interested.
 
Tony Clark said:
Hi All
I am looking to replace my cockpit carpets and would like to hear from anyone who has replaced their carpet with any of the faux teak deck type materials and if so where you got it from.
Click to expand...
Hi Tony,
I haven't seen you on in a while. Are you still making the replacement bilge vent covers? I've had a few people asking me but my fiberglass guy is pretty much retired.

Todd
 
Tony Clark said:
Hi All
I am looking to replace my cockpit carpets and would like to hear from anyone who has replaced their carpet with any of the faux teak deck type materials and if so where you got it from.
Click to expand...

I replaced my cockpit carpet with Infinity Luxury Woven Vinyl. While I didn't select a faux teak pattern, I can say that I love the look and quality. Quint4 on this forum actually made my vinyl, he does outstanding work.
 
bobeast said:
That dual-voltage TV will always run off the inverter as long as it is supplying power. This is less efficient than running the TV directly from DC. Twe're it me, I'd set it up such that the TV always runs off DC.
Click to expand...
peaking of this , there is the old tv antenna control in the same compartment which isn't used anymore. is there 12v power to that? im wondering if I can grab it from there
 
domer94 said:
peaking of this , there is the old tv antenna control in the same compartment which isn't used anymore. is there 12v power to that? im wondering if I can grab it from there
Click to expand...

It does run on 12V, but its wires are too small to run a TV. There is a bundle of wires that runs behind that little TV amp panel. You may be able to tap into something there.
 
Anybody had this problem: I have the original Protech 1230i battery charger on my '99 330 Dancer. This spring I replaced my 3 batteries, 2 starters and 1 house, didn't replace the 4th battery to the genny- removed it not using the generator. This past weekend I went to the boat to find all 3 batteries dead. No DC switches were on and the only AC items on were the charger and outlet switch but nothing was plugged in or no lights left on. I can find nothing that would have caused all three batteries to drain. Could it be a bad charger? Any ideas?
 
Geowh said:
Anybody had this problem: I have the original Protech 1230i battery charger on my '99 330 Dancer. This spring I replaced my 3 batteries, 2 starters and 1 house, didn't replace the 4th battery to the genny- removed it not using the generator. This past weekend I went to the boat to find all 3 batteries dead. No DC switches were on and the only AC items on were the charger and outlet switch but nothing was plugged in or no lights left on. I can find nothing that would have caused all three batteries to drain. Could it be a bad charger? Any ideas?
Click to expand...

Make sure your AC converter was on at the panel. I left mine off before and the batteries drained over the course of a week or two.
 
tdschafer said:
Hi Tony,
Hi haven't seen you on in a while. Are you still making the replacement bilge vent covers? I've had a few people asking me but my fiberglass guy is pretty much retired.

Todd
Click to expand...
Hi Todd
Ive been busy building my house and the boat and stuff has had to take a "back seat" until we move in :(
Yes, I have a port and Stb side ready to ship if you know of anyone who needs them
 
Last edited:
Getting back to the question about the spot light that won't move vertically. Where are the 2 fuses located that would control the movement of the light?
Thanks
 
289447.jpg
searay495 said:
Getting back to the question about the spot light that won't move vertically. Where are the 2 fuses located that would control the movement of the light?
Thanks
Click to expand...
Pull up the 2 square covers to the right and left
 

Attachments

  • 289447.jpg
    289447.jpg
    167.6 KB · Views: 128
OK. Thanks. I have a different set up. I Have a 380 that has a dial type of pad. Rotate it left and right or up and down.
 
I've seen several posts concerning replacement of OEM gauges. I've been thinking about replacing mine as a few of them are getting a little wonky, and some of the aftermarket styles will really add to the curb appeal. Fortunately the burl dash panels were well covered over the years and not suffering from fading so I won't have to replace them. I really like the look of the Faria Chesapeake white with chrome trim rings, but it seems like the 2" engine synch gauge may no longer be available. I may have to go with the similar gauge in black and sub in the Legends series 2" synch gauge from FP. Any suggestions or advice will be greatly appreciated!
received_10155381909797776.jpeg
 
Tony Clark said:
Hi Todd
Ive been busy building my house and the boat and stuff has had to take a "back seat" until we move in :(
Yes, I have a port and Stb side ready to ship if you know of anyone who needs them
Click to expand...
This member reached out to me in January but my guy is basically retired.
 

Attachments

  • Screenshot_20180803-090742_Chrome.jpg
    Screenshot_20180803-090742_Chrome.jpg
    76.1 KB · Views: 141
sr330daguy said:
I got that height ,with a shipping blue print of the boat I have from Sea Ray .I have it in PDF but don't know to post it. Shoot me a PM and I can email it to you guys.
Click to expand...
hows it going, iwas wondering if you still have the shipping blueprint of the 1995 330 da v drives
 
sr330daguy said:
I got that height ,with a shipping blue print of the boat I have from Sea Ray .I have it in PDF but don't know to post it. Shoot me a PM and I can email it to you guys.
Click to expand...
if you still have this can you send it to me. thanks Hans
 
Iwas wondering if there is one for the back to show prop width and exaust location
 
You must log in or register to reply here.

Forum statistics

Threads
113,143
Messages
1,427,143
Members
61,054
Latest member
MrMckinzey
Back
Top