Official 330 Sundancer Thread

can any of you mid 90s 330 guys tell me where to find this? I hunted FP no luck
View attachment 71165
Sure looks a lot like this Blum Compact 1-3/8 in. Overlay Face Frame Cabinet Hinge
https://www.homedepot.com/p/Richeli...-Cabinet-Hinge-2-Pack-BP3336023180S/202209196
richelieu-hardware-cabinet-hinges-bp3336023180s-64_1000.jpg
 
fantastic! . I thought I was looking for the unicorn on this one. do you think they have it in the store?
I doubt it is on the store shelf. Free Ship-to-store and you'll have it in four days.
If HD turns out to be a dead end, you can search for it by Model # BP3336023180S
 
My old boat went through this. I replaced distributor cap and solenoid and one of the two solved the issue.
check your water pressure senor by the distributor. If it is fault in will shut motor down and or limit rpm's. Check your impellers on sea water pumps also. If it is getting hot could be a water problem or sensor problem.
 
Looking for a rudder. Sea Ray part # 604850 casting number 26342.
Sea Ray labels this part as "rudder 310SB, 350EB”.
 
I’m also looking for the seat and cushion the joins the 2 rear benches into a sun pad.
 
I have the table. Looking for the table pad and the 2 pieces next to it
 

Attachments

  • A4731F85-12D2-474E-8678-68201EF875AB.png
    A4731F85-12D2-474E-8678-68201EF875AB.png
    669.8 KB · Views: 215
Has anyone encountered this & how did you remedy it? This is the boarding ladder cover that has vibrated away the gel coat on the platform below it posterior edge. I plan on getting the platform repaired at seasons end but dont want to deal with this getting any worse.
20190615_143805.jpg
20190615_143756.jpg
 
Has anyone encountered this & how did you remedy it? This is the boarding ladder cover that has vibrated away the gel coat on the platform below it posterior edge. I plan on getting the platform repaired at seasons end but dont want to deal with this getting any worse.

I have that issue but no where near as bad as yours. If only shows underneath and there is no gel coat chips on mine. Maybe grind down those edges a bit and add some vinyl U-channel held on with 4200 along those 4 spots that touch?
 
I think that he is missing the insert & cushion that tie the aft bench to the rear facing bench to create the U shape seating as well.

Maybe, but his picture shows it installed. Maybe the picture is not his boat though.
 
I have that issue but no where near as bad as yours. If only shows underneath and there is no gel coat chips on mine. Maybe grind down those edges a bit and add some vinyl U-channel held on with 4200 along those 4 spots that touch?
I'm thinking that too. I will see what the marina recommends. Not sure where to get the vinyl U channel. Last time I looked it seemed most had metal ribbing reinforcing it. I cant use that as it gets pretty wet with salt water back there.
 
The picture is not my boat was using to show what I was missing since I wasn’t sure of what they were called. Yes, I am missing the insert & cushion that tie the aft bench to the rear facing bench to create the u shape seating and the cushion for the table.
 
I am looking for a swim platform for my 98 330. I have a soft spot in it and would like to switch it out. Does anyone have suggestions on maybe a fix.
 
I am looking for a swim platform for my 98 330. I have a soft spot in it and would like to switch it out. Does anyone have suggestions on maybe a fix.

Ok, there must be a story to the boat you bought. You have a lot of things that are missing or need replacement.
 

Forum statistics

Threads
112,946
Messages
1,422,757
Members
60,929
Latest member
Henchman
Back
Top