Official (1998-2002) 310 Sundancer Thread

Martyr Anodes CMDIVERA ALUM DIVERS DREAM 1/2INX6INX12Qty 1 - L-194-CMDIVERA
Martyr Anodes CMR03AL RUD ANODE CMR3 3-3/4 Qty 2 - L-194-CMR03AL
Martyr Anodes CMX07 1 1/2 ZN SHAFT ANODE Qty 2 - L-194-CMX07
http://www.boatstoreusa.com/
 
Does anyone know if there is a circuit at the helm which has 12v power only when the engines are running (or the ignition switches are on)? I am connecting the Bennett EIC 5000 tab control and want the auto retract function. The wire that does that needs power when the engines are running but no power when the engines are off.
 
Anyone looking for the rear cockpit carpet i think its honey berber.
I replaced my carpets with new. I bought the boat last october last owner only replaced the rear carpet.
Other two were shot still trying to get the backing off the floor.
It's in good shape has the other backing on it not the black stuff.
 
Sal A said:
Have you checked all your fluids dt0116 I once had an io the drive fluid was a tad low and would sound the alarm when the boat pitched or I accelerated
Click to expand...

I have v drive, but might have something to do with that, I was thinking something was loose wire wise maybe
 
I'm looking for the T clips that hold up the curtains in the tracks, anyone know where I can locate them? I am also looking for a zwaardvis table leg either 26" or 27.5" long. Thanks
 
Last edited:
I have about 15 feet of new rubber gasket for bottom windshield channel if someone needs it. I won't bend you over like Taylor Made did to me. Made me buy more than I needed, paid 3.85 a foot, plus 25 "Taylor Handling Fee" and 14 for shipping. Anyway, you cover shipping and I will let it go for 3 bucks a foot.
 
Does anyone know the model number for the Raymarine radar dome, stock on a 2002? I might need a new cover for mine. I have the RL70C head unit. Thank you.
 
Does anyone know how to center a steering wheel? I have a hyd sea star system with inboards
 
I believe you cannot center it as it can over center turn due to the hydraulics or something like that.
 
Hello 310 owners. This I my first post. I purchased a '99 last summer and have been getting her ship shape and updated. Learned a ton from all the previous posts. Thank you.

All new electronics, NMEA 2000 Backbone, Standard Horizon AIS Radio (MMSI), Garmin 840xs, Radar, sonar, analog to NMEA engine gauge system, entertainment system. Converted all lights to LED. New wiper motors. Those were a bear to get to. Lots learned and more to come.
 
Last edited:
cfd95 said:
Anyone looking for the rear cockpit carpet i think its honey berber.
I replaced my carpets with new. I bought the boat last october last owner only replaced the rear carpet.
Other two were shot still trying to get the backing off the floor.
It's in good shape has the other backing on it not the black stuff.
Click to expand...

cfd95 - does the carpet have the table leg cut out?
 
Hey there, while my carpet is ok, I'd like to hear more about your nmea engine gauge set up. I have a 2000 310, 5.7 horizons and was told they predate outputting any performance information. Thanks.
 
Boston-boater said:
Hey there, while my carpet is ok, I'd like to hear more about your nmea engine gauge set up. I have a 2000 310, 5.7 horizons and was told they predate outputting any performance information. Thanks.
Click to expand...

Boston-boater, Noland Engineering has a couple of products that take analog data (resistance) and convert that to NMEA 2000 or 0183. The analog data can be captured at the sensor, or at a dash gauge (using the SEND "S) post on the gauge. Their software lets you set the type of data being captured. It takes a little while to set the analog range of each device...like engine temp and oil pressure. One RS-11 can give you 2 engine data for RPM, plus 6 other analog inputs. I captured RPM, Temp, Oil Press, and fuel level for both engines.
 
You must log in or register to reply here.

Forum statistics

Threads
113,118
Messages
1,426,471
Members
61,034
Latest member
Lukerney
Back
Top