Search results

I tried the Bemis set on my 2002 Sea Ray 380.it is about 2” too long. Any other ideas?

I replaced the Crank Sensor today and let the boat run for an hour. Engine was at full temprature and the hatch was closed. I did put in a crank sensor from a 2002 Chevy Surburbon 8.1 and it was 74.99 Thanks for everyone's help! For future reference to my fellow boaters. This part took a whole...

So I came up to the boat and was ready to pull out the crank sensor but tried to start it to make sure I still have the same issue. Guess what, it started and sounded fine. I let it run with the hatch open and revved it a few times, all good. I closed the hatch and left it idling and a few...

Thanks all for the replies. I'm going to the boat in a bit to hopefully fix it. Wish me luck!

I have a similar issue. I was out this weekend cruising around 25knts and started to throttle down and my starboard engine died. It just stopped, no sputtering. It cranks fine, has fuel pressure in the rails but doesn’t have spark. It didn’t throw any error messages on the system monitor either...

Thanks Chris. I called Southcoast marine and they asked for the part number of the Anchor. Any idea about the part number or can you recommend a galvanized one? I see the Delta type anchors but not sure of those are the right ones.

I have a 2002 380 Sundancer and I lost my anchor last weekend. I’m looking for a new one and need to know the weight of the one that came originally. Was it 35 or 22 lbs. I’m on lake Lanier so it’s pretty tame. thanks for your help. Ray

I’m replacing the stereo and removing the 6 disk changer. I have a new fusion head unit and want to replace the off white melamine board and cut a new hole. Does anyone know where I can find a replacement board without holes? Thanks, Ray 2002 380 Sundancer

I have a 2002 380 Sundancer. The outlet in the kitchen isn’t working. I also noticed the coffee maker is hardwired to somewhere and I want to remove it. is there a hidden outlet or GFI?

After a bunch of research and information from my fellow Sea Ray friends I decided to get a replacement fridge. I got the Norcold DE0061 and it will be delivered in a few weeks. I haven’t decided if im going to do this myself or find someone.

How do I measure the burn at different speeds? I am running a 2002 380 SD with the 8.1 engines. Thanks, Ray

What model Vitrifrigo is everyone installing in their Sea Rays? Thanks, Ray

I got the plugs changed. The socket size is 13/16 thin wall with a a wobble extension. The plugs were shot and wasn’t firing on 3 cylinders. New plugs and it ran smooth but there’s gas in the oil so that’s getting changed.

I have a 2002 380DA and the engine is running okay with no load but it struggles when there is a load placed on it. It also smells like raw gas. It’s not blowing black smoke. I want to try to change the plugs to start with but I can’t get the right socket on them. is there a special socket or...

I need this too. My microwave goes on for 3 seconds and shuts off.

Tdb380Ray - same here. Bottom is fine but the top takes 20 tries.

I have a 380 DA. The back power seat goes in and out without any issues. The part that is barely working is the back seat incline. It sorta works if I keep tapping the switch but eventually trips the breaker. Any ideas on how to fix this? Thanks, Ray

Thanks for the responses. I went up and found a small leak on the line connected to the hot water heater. I fixed it and cleaned up the water. Praying I don’t go up there in a few days and have water again. Ray

I just purchased a boat and it was out in the rain a few days before shipping and also during shipping. When it arrived I noticed the floor by the back couch to be sopping wet. I’m going to bring the wet dry vac tomorrow to get most of the water out. Any ideas why the back floor would have...

I’m purchasing a 2002 380 Sundancer and am contemplating the same decision. How hard is it to remove and reinstall the Arch? Is it heavy or can 2 people lift it? Thanks, Ray