Search results

I have two of these antennas on my hard top. They are not the GPS antenna. They have a very thin wire coming out attached to coax. Any thoughts on what they are would be appreciated.

No longer needed on my boat, all electronics were switched to Garmin before I bought it. If somebody needs it, I will be glad to ship it off, $25 including shipping.

By some chance can somebody tell me what this is? I believe it was used on a Raymarine system.

This membrane was taken off the boat about two years ago. Not sure if it was pickled properly or not, if somebody can use it make me a reasonable offer plus shipping and its yours. It is 48" long and about a 2.5 " diameter.

I have the Apollo 3" flange mounted ball valve seacocks. They have two 1/8 caps, one on either side. Trying to get info from Apollo has been difficult but I am told they are to flush fresh water to clean out the salt. Does anyone out there have experience on doing this? Just curious on the...

Asking $50 plus shipping Faucett from Sea Ray Sedan bridge. Used but excellent working condition.

Hello, the joystick power button will activate, but once i try to use bow thruster it goes off. I believe it is either the thermo switch or the control box. after further review I see the wire from the thermo switch plug looks like it is not in the control box all the way (see picture attached)...

Hello, I am having a problem with my master head. I replaced everything from the floor up in the head, down below I replaced duck valves, I replaced the bellows, I replaced the vacuum switch twice because Dometic and a local repair shop said they are having major problems with their switches...

On my 2005 550 Sedan Bridge I have the hydraulic swim platform. Recently I noticed some water in my bilge. Not a great deal of water but it wasn't there before. After tracking it down, I noticed a wet spot on the transom right below where the swim platform brackets would be on the outside. None...

Hello, my boat has two 8D batteries for my bow thruster. I realize it is a 24 volt system but I cannot find a definitive answer on why I cant use two group 27 or 31 instead of 8D's. The batteries are only for the thrusters. Any thoughts on this subject would be appreciated.

Ready to do some updates to the master head wall panels. Before I dig in, has anybody had experience on removing the ceiling panels? Not sure if they are mechanically mounted in some way or just Velcro. Thank you

Hello, on my 2005 550 Sedan Bridge the holding tank is not reading correctly. I already flushed with clean water and a packet of tank buster. Still reading the same, so I am thinking sending unit. Of course it is located behind the generator and difficult at least for me to get to. Any thoughts...

On my helm there is a trim piece that is glued in place (see pictures). There are no mechanical fasteners holding it in place. When the temperature heats up from the sun it pulls away about 2 inches or more. I have tried gluing it back in place with different adhesives and it holds for a while...

I have the Onan MDKBD generator and the heat exchanger cap is leaking. The generator runs great and at normal temp. I flushed it out a year ago and was just thinking of changing the cap and gasket. Not really familiar with generator work so the question is, am I wasting my time on just changing...

Hello, I was doing some routine maintenance and took a look at the bow thruster. I have the Max Power CT165. I noticed what looks like a oil spray from both sides of the shaft. I do not believe there oil or a oil reservoir anywhere on the motor. Any thoughts on what might be going on? I attached...

Hello, I have the ONAN H040684075 generator that always ran great. For some unknown reason it now shuts down. Starts great, sounds good but shuts down after about 5 to 7 minutes of run time. Pumps plenty of water so impeller not the issue. The fuel and fuel filter looks clean, plenty of oil...

I have flushed my lines out with fresh water but I would like to do a closed loop with some descaler like Barnacle Buster. The supply line from the sea strainer is easy. However, I cannot find where the return line is feeding the outlet tubes. Since it drains from both sides there must be a Y...

My rudder indicator started acting up on a cruise yesterday. At first the gauge was reading a hard to port indication which wasn't true, I was going straight. Now it is reading straight regardless what I do with the wheel. The sensor below looks good, nice and tight. Is there a way of checking...

Sorry if this sounds more like a venting but this is one of the most frustrating projects so far. I had to replace my water heater which I thought removing and replacing the unit was going to be the hard part, it wasn't. wiring the unit no problem. Now for the problem, the hot water line...

The two water lines for cooling/lubricating the prop shaft. One line goes to the oil cooler in the gear box. The other line goes forward through bulk head or at least that is the way it looks. Where is it going and where does it pick up the water from? Thank you