Search results

Just replaced bulb with OEM Marinco bulb - just didn’t want the hassle of rewiring LED. Does anyone know where I can get a new rubber gasket to seal it. It is not listed in the parts manual? Thank you.

Windlass issue now UGH! Everything worked perfectly last week. Now, the windlass brings the anchor UP no problem. However, it will not drop the anchor. I goes for 2 seconds then stops and just spins. The chain is not balled up. Even when I remove it all from the gypsy wheel and manually...

Can you tell me where that is located? I figured I might be missing something. thank you.

I am stumped ... 2007 340 Sundancer with 8.1 inboards. Upon launch, the port engine alternator seized and the serpentine belt broke. Alternator was replaced, new belt installed; ;however, during installation we forgot to turn off batteries. The batteries are new as of May 2020 btw. We...

I have the exact same boat and looking to tackle this project. What TV did you purchase? Any tips and suggestions for installation? Thanks.

Thanks again! I just fixed it and your posts were absolutely correct. Now, i can work my reading lights independently.

This will be HUGE! Thank you for searching and posting. I can't claim to be even a novice electrician ... are you taking about the light switch under the AC panel? All I have to do it pull it out and switch one wire? Can it be that easy? :-) Thanks again!

V-berth light issue: This is my first season with the 340 and have a quick question about the reading lights in the v-berth. The lights appear to be wired with the overhead lights above the closet and above the portside step to the bed. They all turn off and on with the switch under the AC...

So I have narrowed the issue down to the aft EIM in the bilge ... nothing noted on that EIM is working. All of the breaker buttons are pushed in and there is power getting to the board. Are there actually fuses inside that board? thoughts? Thanks.

Hi Henry - what are the mini breakers in the EIMs? I pushed the "buttons" back in

Electrical problems? Got to my boat and the blower, cockpit lights, anchor, bildge pump, aft acc, don't work. But the arch lights, radio, water all work. None of the breakers where the switches are were tripped nor any by the helm. I went to the circuit breaker in the bilge and the blower was...

V-berth closet shelves??? Weekend project to finally install some shelving in the v-berth closet, the undersink cabinet, and the TV cubby. Has anyone added shelves here before? Templates? Thanks.

"When is the last time the raw water impellers were changed? Did it get over 170? Did you get an alarm? I don't remember the exact spec temp numbers for the V6 engines but I think 165-170 is pretty normal. Any higher than that really and you have a problem." Normal temp for my engines is...

I have the same question ... I can't figure out how to access the bulb in these lights and I don't want to break the swivel light. Does anyone know how to change the bulbs?

Head Sink Faucet Leak Does anyone know how to fix this issue? The sink/shower faucet leaks which means my pump run quite often. I have to use the black button on the side to ensure that it does not drip. If the button is not pushed, the faucet drips. How can I fix this leak and save my...

I purchased and installed (simply screwing it in) a drain plug light. Does anyone know how I can wire this light? It has red and black wires and I would like to use the ACC2 switch at the helm to turn it on and off. I have a 2006 280 DA. Thanks

I got it started. There were two switches on the front a light switch type toggle and a horizontal run auto switch.

No there is nothing showing on the display. It is blank.

I can't get my generator to start. The switch on the actual generator is switched on; however, the display remains blank. I tried starting from both the cabin and the engine room. It doesn't even turn over. Is there a battery that isn't charged with the converter? Could that be it?

I can't remember from last year ... When hooking up to dock waterline. I am currently hooked up to the dock waterline and if i remember correctly i should not have to turn on my waterpump. Is this correct? Right now i can't flush the toilet or get any water in the sinks without the pump on even...