Search results

  1. Mick & Denise

    Large boat lift for sale

    I am going to be selling my 50 ft Sundancer and I am posting to see if anyone has a use for the lift. It can fit any boat up to 15 foot beam. My boat weighs around 50,000 lbs. It runs on hydraulics and is maintenance free except a grease gun once a year. I have been lifting my boat for 4 years...
  2. Mick & Denise

    Don't forget to file your fuel tax refund for NC :)

    Thanks for the info! My accountant is working on it now. I definitely will go back the 3 years on this one. Thanks!
  3. Mick & Denise

    Don't forget to file your fuel tax refund for NC :)

    What forms are they? I have, let me say "PLENTY" of fuel in a years time that would love to get something back on. Thanks for the heads up!!
  4. Mick & Denise

    Cat or Cummins power?

    I had the 3208"s in my 44ft. I had very good luck with them without much maintenance. Now I have 3176's. Bad move on my part.
  5. Mick & Denise

    2012 Rendezvous--Coastal Carolinas Club Sea Ray Members

    Ringing in from the Belhaven, NC. area. Will be heading down to Beaufort/MH for the seafood festival Columbus day weekend. We love the trip down there from here.
  6. Mick & Denise

    WTB...50ft dancer props

    I am sorry, I mis-typed. I have 4 blade props 26 x 26. But am thinking about having them re-pitched to 24 x 26 to get on plane easier.
  7. Mick & Denise

    WTB...50ft dancer props

    Hello Rogman, Is that the size props it came with? I have the 600 HP with 3 blade 26 x 26 props and that is the max I can do for the HP I have. With you going to a 4 blade 26 x 26 you may not have enough HP to get on plane. Just a thought if you have 3 blades on there now.
  8. Mick & Denise

    Crystal Coast NC

    We are up here in Belhaven but get down your way a few times a year. We go to Ocracoke 5-6 times a year also, Washington, NC about the same. We will keep an eye out for ya's!
  9. Mick & Denise

    Are all political views welcome in this forum?

    Voice that opinion. Most people on here actually have to earn their own money to pay for their boats and therefore most of the opinions you see reflect that. Did you have you boat given to you by an uncle that passed away?
  10. Mick & Denise

    low RPM at full throttle

    My boat will not run full RPM or even get up on plane with barnacles on it. They make a huge difference. The first time I had a fouled bottom on my 27 ft I thought I had major engine troubles untill I pulled it out of the water and saw how many barnacles it had. Cleaned them off and was just...
  11. Mick & Denise

    velvet drives fluid change anybody ?

    I just changed the fluid after a rebuild on the BW Velvet drive 5000 series. There is a drain plug at the very bottom of the drive just behind the coupling on the output shaft. It came out fairly easy. If I remember it took a 1/2" wrench and was a square head. It only took 2 quarts to fill it...
  12. Mick & Denise

    97 Sea Ray Sundancer 500 Fuel Vents

    Your have to take out the couch section to get to them. The straight part will come out but it is like a puzzle. The first time I did mine it took me almost 2 hours. But after you get the seat out the base is screwed in with back panels on it. The screws come in from both sides and some up...
  13. Mick & Denise

    Westerbeke Question

    I just replaced one about 2 weeks ago on a freinds boat with the same genny. Went to Advance auto and no one knew what a ballast resistor was so i had them look it up for a 1972 Dodge Dart. Then they pulled it up and it has worked fine with that one.
  14. Mick & Denise

    Official 370 Sundancer thread

    Thanks Gyrospiro, Sea Ray did verify that also. I do appreciate it!
  15. Mick & Denise

    1998 370 Sundancer transmission

    It is a 1998. Any ideas on the ratios?? Thanks again.
  16. Mick & Denise

    Official 370 Sundancer thread

    Can anyone tell me what kind of v drives you have in your 370 Sundancers with 454's? The year is a 1998. Thanks for any info in advance!!
  17. Mick & Denise

    1998 370 Sundancer transmission

    Does anyone know what brand and size the v drives are in a 370 Sundancerwith gas 454's? It's not my boat and trying to find out for a freind. Thanks
  18. Mick & Denise

    What did Ms O say?

    WoW! That explains a lot. Hows things up on the Hudson Tom? From Albany originally here.
  19. Mick & Denise

    Aquapalooza in Wrightville 7/24

    Thats about right. We are comming from Belhaven which is about 82 miles from Beaufort. We will not take the Intracoastal and will be navigating straight from Beaufort inlet to the Massonboro inlet wich should be about 2 hrs across. We will be taking the Intracoastal from Belhaven to Morehead...
  20. Mick & Denise

    New floor!!

    Sharp looking floor. Great job!
Back
Top