Search results

I called Faria Beede ( Phone # on gauge )the manufacturer of the gauge and spoke to technical support they told me to send them the gauge and for $125 they would repair it or send me a new one. So I packed the gauge up in a box and sent it to them prepaid $125 on a credit card yesterday I get...

My question is the drain wire in this cable number five in the instructions. Where should this wire be installed on the negative terminal block on the top with the negative power lead or should it be with all the negatives that are marked for electronics only

This is my first season with a diesel boat QSB 6.7 HO, So I did a lot of research here as well as the internet. From what I see fuel management is as important as changing the oil. I attached a picture of the Racor fuel filter I changed, Should I be concerned about the black on this filter or is...

I need to reseal my windshield do to a small leak. What sealant / adhesive does Sea Ray use at the factory, Whatever is in there now is very soft. What is the best sealant to use on a cockpit windshield. I tried 3M 4000 UV on my old boat and was not happy with the results after a few years. I...

2015 QSB 6.7 HO I seem to be using more fuel in the starboard motor then the port, About 6 gals at fill up All readings seem to be in acceptable range except for the load readings were there is a 3 % difference, Should this be the same or is it acceptable. I did have the props reconditioned in...

I just got back from Newport RI and Block Island, I traveled on the inside going through the Moriches Bay going and coming back on high tide, I was marking 5' to 7' most of the way. My boats draft is 4' and at no point did I hit bottom or see anything turning up. I have Navionics on my phone and...

Does anybody know a good Cummings Diesel and Zues drive surveyor on Long Island. The boat is in Great Peconic bay marina in South Jamesport. I already spoke to Wesco, But would like to talk to a few more on availability and knowledge.

I have a deposit on a 2015 410 DA in California, I have scheduled a marine surveyor, mechanical survey, Haul out and a captain ( In California you need a captain to drive the boat out of the marina ) for this Wednesday. I am supposed to fly out tomorrow 6:00 pm and land in California at 9:30 pm...

Does anybody know of a marine in NJ on the Hudson that will remove a 410 boat off a trailer and put it on the hard for a week while I reassemble the radar, props Etc. I already called Liberty Landing and would like to talk to a few other marinas.

I am thinking about buying a 2015 410 and having it ship but to do this I need to have the radar removed. My question is, On a newer boat is there a plug or maybe a splicing block to separate the wires, if not can the wire be cut and soldered back together. What is the best way to do this...

Does anybody know a Cummins Diesel and Pod survey around Quincy Massachusetts area. Just put a deposit on a 2014 410 and need a motor survey ASAP, As we are looking to close on 12/18/20 Santa has been good to me.

I just put a deposit on this boat. https://www.yachtworld.com/boats/2017/sea-ray-400-sundancer-3696068/ Does any know a Hull surveyor and Diesel surveyor in the Port Pierce, Florida area. Looking for someone good and don't want to use the brokers survey. Also need a Capitan to take a ride with...

Here is the boat https://www.boats.com/power-boats/2015-sea-ray-410-sundancer-7548379/ I am real close to putting a deposit on this boat, My big concern is the quality of the boat because of sea Ray getting in trouble and cutting back on everything. All the surveys I talked to said just make...

Does anybody have this boat, how is it in a heavy seas, How does the boat handle in general. How are the Cummins QSB 6.7 480HP, Any known problems or known recalls ? The boat has the Cummins joystick docking system, Good or bad ? The boat has V drives with bow and stern thrusters, Does any know...

Looking to put a deposit on this boat but it is in Florida so before I fly down there I am trying to put together as much information about this boat as I can before I go. 2017 40' Sundancer with QSB 6.7 480 with 217 HR, boat has V drives, Bow thruster, Stern thruster with Cummins joystick...

Looking to put a deposit on this boat but it is in Florida so before I fly down there I am trying to put together as much information about this boat as I can before I go. 2017 40' Sundancer with QSB 6.7 480 with 217 HR, boat has V drives, Bow thruster, Stern thruster with Cummins joystick...

Trying to help a dock neighbor with a 2016 8.2 HO with catalytic converters that is throwing a code. He got a code on the vessel view that said Starboard engine Misfire so he took it to a certified MerCuiser dealer at the end of last season and they said that there was a crack in the exhaust...

When SmartCraft tells you bad sensor on engine # 1 is it referring to the Port or Starboard motor. I am pretty sure it is the Starboard, ( Brain fart ) just want to make sure before I change anything.

Does any one know what type of antifreeze the 2008 Kohler 7.3 ECD generator takes. It is a pee color so I am not sure and I called Kohler to get no response.

My friend is buying a 2016 Sea Ray Sundancer with twin 4.5 Hp and Bravo 3 stern drives he is concerned that this boat is under-powered. He ask the dealer to have full gas tanks and water tank and the dealer said there is just under a 1/4 tank of gas in both tanks no water and they are not going...