Search results

  1. T

    Identification of fuse box at the helm

    1998 370DA has a fuse box at the helm (not breakers but fuses). The lettering as to which fuse/connection is on the box has faded and can't be read anymore and I'd like to know what each fuse is powering. Specifically the most forward row of connections has 4 red wires and the wire on the far...
  2. T

    Adhesive to re-glue the rubber gaskets under the floor

    As I pull up the floor to go down to the bilge area the rubber gaskets are just pealing away. They are in excellent condition and a little goo-gone takes the now slime adhesive right off. What can I use to re-glue them back on and not fall off because of the heat. This is rubber to fiberglass.
  3. T

    Recommendation for new canvas replacement in Middle River Md

    Any recommendations for a shop to make and install new canvas for my 1998 370DA? Also does anyone recommend the thicker plexi for my helm canvas?
  4. T

    Removing sea-fire G500A fire suppression in bilge 370DA 1998

    I have the Sea-Fire G500A on my 1998 370DA. I don't see a place where there was a pin or where a pin could go into stop it from going off. This is original to the boat I'm positive. I see an electrical connection to the bottle but does anyone know if I unscrew that connection will the unit go...
  5. T

    Remove automatic fire extinguisher system

    I have the Sea-Fire G500A on my 1998 370DA. I don't see a place where there was a pin or where a pin could go into stop it from going off. This is original to the boat I'm positive. I see an electrical connection to the bottle but does anyone know if I unscrew that connection will the unit go...
  6. T

    Official 370 Sundancer thread

    i don't but am looking for my son to recreate the stripes and decal - Hes a graphic designer. When he gets them done I'll let you know. I could sent the file to you have you can have someone that prints boat name letters cut it out.
  7. T

    Official 370 Sundancer thread

    Not sure the difference or how to see the profile. I was afraid to rip the cover out of the channel since we are getting rain. I do have stainless steel - I'm pretty sure. Do I need to just pull it out to check? Did yours look like this? It's about a inch wide.
  8. T

    Suggestions for replacing the raymarine radar on a 1998 370DA

    Well I upgraded to a Garmon 741XS chartplotter however i'm not a fan of running the Garmon radar though the 741. I just like a bigger display for radar like the old Raymarine that came with the boat. I don't see a Garmon radar only option? Does anyone know if there is an option since I...
  9. T

    Engine repower with newer engine or just rebuild?

    I started following the Facebook page of the shop that's doing the rebuild and they were featuring it on their page (big smile).
  10. T

    Official 370 Sundancer thread

    No luck in my binder. I'll have to go the the boat and pull a piece up and take a picture and send it to them. I wish the rain would stop though.
  11. T

    Official 370 Sundancer thread

    Need to replace the window gasket that covers the screws in the track on the windshield and side glass. Does anyone know what and where to buy? Mine is way over due to replacing. Do I need to go pull a piece up to figure out the profile or on a 370 DA 1998 the pasts place(s) will know?
  12. T

    Official 370 Sundancer thread

    That is a very nice job! I like the way you made the templates using tape as the cutting edge.
  13. T

    Help identifying the what size breaker is the fresh water pump 1998 370 DA

    Just found that the breaker is a 10 amp breaker. I need to find a low noise less than 10amp freshwater pump.
  14. T

    Help identifying the what size breaker is the fresh water pump 1998 370 DA

    Yea - it trips the breaker - will change that in the post. The old pump was out of production and the Marine Parts Store (I mean a real marine parts store with a only a parts counter (not a W__t Mari-e type). I took the pump in and questioned the difference between a wash-down and a freshwater...
  15. T

    Help identifying the what size breaker is the fresh water pump 1998 370 DA

    My old fresh water pump bit the dust two years ago and I asked the marine store to get me a replacement. Don't remember what I had on the boat but they gave me a JASCO PAR-MAX 4.0GPM "washdown pump". Said that was fine to use as a replacement. This pump says it's 15 AMPS at 60 PSI and then...
  16. T

    Engine repower with newer engine or just rebuild?

    can anyone tell me how to "break in" a rebuilt engine? Someone told me years ago that engines get broken in over about 10 hours but I'm not sure what that means. Also, the starboard engine it the one I lost to my surprise because it had been the port engine that needed to work harder to sync...
  17. T

    Engine repower with newer engine or just rebuild?

    Thanks scoflaw and Rusted Nut. The engine shop is going to get the engine running and break it in from what I was told but will verify. I'm not sure what that entails though. The rebuild shop is a hot rod and marine engine build shop as that's all they do. They just rebuild so the engine...
  18. T

    Engine repower with newer engine or just rebuild?

    Update. Marina sent the engine to the local machine shop they deal with and I've list several cylinders, as I expected from a compression test done about 2 months before the engine stopped. The rebuild is $6,000 with new heads and the the marine said that there is about 8-9 hours to drop it...
Back
Top