Search results

Hello all My 2009 350 dancer (2010 370) did not come with foot rests for the helm or the companion seats. Has anyone installed these? Any advice? Also, any idea where I can purchase the foot rests and hardware? TY

Has anyone heard of riser/elbow internal welds failing on 8.1s leading to water leaking into heads and damaging valves? I’ve heard this story several times and am trying to find out if there is an issue with mercruiser OEM risers? I’m looking at replacing manis and risers but don’t want to...

Boats!!! So yesterday I’m down at the dock watching TV and I notice the digital channels had poor reception.Today I go up to the antenna mounted on the hardtop, remove it by loosening the set screw, remove the antenna cable, (looked crappy) and install a new type f connector and remount the...

hello all I have the Atwood ehm6-sm hot water heater. On the thermal cut off switch there is a little button to “reset” the switch. I have reset it several times before as it usually trips if you turn on the hot water heater prior to turning on the fresh water pump. At this point, it no longer...

hello all Both dripless shaft seals began leaking. First the port, although the drip is minimal even under load. About 2 weeks ( and several trips) later, the stbd seal started leaking pretty good under load, enough to activate pumps after 30 minutes of running time. When motor is off the drip...

Hello all Does anyone have suggestions on the best tools to use to loosen the locking nut on the stbd rudder post? It’s really tight. My pipe wrenches that fit the nut are too long. I have a short flange wrench that I can get on the nut however the handle is to short to get any leverage on the...

hi all I’m hearing a squeaking from my port motor that gets louder with added throttle. Sounds like a bearing noise. The tensioner was replaced last summer. The belt seems ok. If I spray some wd40 directly on the pulley shaft screws for the water pump ( being careful not to spray the belt) the...

hello all and Happy Memorial Day Was going thru my monthly check list before the weekend. When activating the soft key for the bilge pump, the blue indicator light began flashing and the pump did not activate. So I then went into the bilge and operated both the bilge and high water pumps thru...

here is an interesting issue I ran into today on my 2009 350 dancer 8.1 v drives. The following fault appears on vessel view: Eng 2: engine sensor Manifold absolute pressure sensor not working properly. This fault will result inreduction of engine performance. So not knowing which is engine...

Hi all In looking at the 2009 350 Sundancer (370 in 2010) owners manual standard system stereo schematic on page 42 it shows 3 amplifiers: 1 for the cockpit, 1 for the cabin, and 1 for the transom speakers. I’ve located the cockpit amp which is a Panasonic in the mid cabin stbd side storage...

Hi all I have an 09 350 dancer (became 370 in 2010) The cabin speakers completely stopped working on the stereo. Working one day, out the next. Assuming the " boat gremlins" didnt attack me as I Installed the "gremlin protection system" (lol) I have found a 4channel amplifier inside the...

hello all My engine hatch was working fine. Then dead. I found what appears to be a paddle bypass switch directly under the helm. It lifts the hatch, however very slowly and requires assistance. The switch located on the stbd helm switch panel does nothing. Looking for any insights anyone can...

hello all During transport the main wiring to the dome was cut on my Raymarine 120c. The wires cut inside the jacket were Red blue black and green. Was hoping I could just re splice them together again, red to red, etc. without replacing entire cable. I’m not familiar with radar, can I just...

Hi all Im purchasing an 09 350 dancer. Ive seen a number of posts on the sound system, I noticed the right channel on the stereo is out throughout the boat. Ive adjusted balance, fader, etc. Nothing on the right side. Swim platform, cockpit, cabin...nothing. Am i missing something? Cant...

hi all The motor on the v birth doesn’t seem to be working. Bed is in up position. Breaker is on. Anyone familiar with these? I get nothing when pushing remote control up or down. Thx

Hi All Im looking at purchasing an 09 350 dancer, 8.1s v drives. The manis are original, 350 hours on motors. I know the exhaust will need replacing given they are original. I have a few questions: While researching parts I see Mani kits with all gaskets etc, and separately elbows which are...

Hi all Im looking at on 09 350 sundancer to purchase. I believe this was changed to the 370 in 2010. 8.1s. v drives and 12 foot beam. The boat is very clean. The records show that the port motor was mis aligned to the tranny and sheared off the bolts. This occurred in 2013. The tranny was...

Hi All Im looking to haul a 2006 340 dancer v drives. The hauler is asking me the distance between the props/shafts. Ive looked in the manual. google etc...cant find it anywhere. Anyone know where I can find this measurement? tx Dan

2006 340 Dancer; Does anyone know where i can find a cockpit sink? The sink has cracked. Also, the actuator switches for the engine hatch lift are intermittent Can the switches be replaced or do I have to replace the entire panel? Thank You!

It appears the "cool" button on my AC controller is intermittent. Do I need to replace the unit? If so Any recommendations on where to purchase? I've see it on line for about 300.00. Any thoughts appreciated.