Search results

  1. A

    Inboard Sterndrive Maintenance in Tampa/St Pete

    Any recommendations for service for a 35 Sundancer with inboard engines and sterndrives in the Tampa, St. Petersburg area - other than MarineMax?
  2. A

    Refrigerators not Working

    Both my cockpit and cabin refrigerators stopped working. Boat is a 2011 330/350 Sundancer. I turned on every breaker on the Distribution Panel and made sure that the breaker (next to the battery switches) for the cockpit refrigerator was not tripped. The refrigerators will not run on battery...
  3. A

    Replacing Anchor Rode

    My 2011 350 Sundancer has the "Quick Slim Splice" rope and chain. The rope is connected to chain using a type of crimp sleeve. The issue is that the connector from the rope to the chain is badly corroded and I am not certain of its strength. The chain and rope is in excellent condition...
  4. A

    How to use Sterndrive Tilt and Trim?

    What is the best way to use the sterndrive tilt and trim tabs on a 330/350 Sundancer?
  5. A

    Source for Ignition Protected Engine Hatch Lift Actuator

    I need a replacement engine hatch lift actuator. MarineMax has informed that the engine hatch lift actuator is no longer from Sea Ray - Part Number: 1766064 ACTUATOR, ELEC HATCH 18”12V INLIN QUIETR. Several on this forum has recommended actuators, however, when I checked none were Coast Guard...
  6. A

    Replacement Engine Hatch Lift Pin

    Does anyone know where to get a replacement pin for the engine hatch lift. Boat is a 2011 330/350 Sundancer. What is the part number of the pin?
  7. A

    Windshield Screws and Gap

    There is a large gap between the bottom of my windshield and the top of the hull deck. The screws were loose. Tightening down the screws pulled the windshield down a little but did close the gap. Should I caulk the bottom of the windshield frame to seal the opening?
  8. A

    Replacing Fuse Block

    My 2011 350 Sundancer has a fuse block under the console that using blade type connectors that push on the spades on the fuse block (similar to the one the picture below but mine is no way close to being organized and tidy). I have a tendency of pulling of a connector and cannot determine what...
  9. A

    EIM Can Bus Advantages/Disadvantages

    I asked this question before, but now I am really curious. What is the advantages of Can Bus system (EIM) over discrete switches? From my reading, I understand Can Bus saves money on installation because various electrical and electronic systems use the same wiring backbone, share information...
  10. A

    2011 Sundancer 330/350 Auxiliary Interface Module

    Does anyone know where the 2011350 Auxiliary Interface Module is located? I looked under the dash console where is located on the 280 Sundancer? However, on my 330/350 Sundancer, I can not locate it there. The Auxiliary Interface Module shows on the wiring diagram but I don’t know where to...
  11. A

    Cutting Hole in Bulkhead

    On a 2011 330/350 Sundancer I need to run some wires from the hatch area up to the dash. On the starboard side there is a bulkhead right under the arch meets the side of the boat. Is okay to put about 3 inch hole in this bulkhead? After I cut a hole and run the wires, do I need to fill the...
  12. A

    Location of the Glomex Antenna Gain Control Splitter

    Where is the 4-way splitter from the Glomex Gain Control on a 330/350 Sundancer to connects to the televisions? The back of my gain control has 3-Coaxial connections (antenna in, shore in and television out). The Sea Ray manual shows the gain control connected to a four-way splitter. There...
  13. A

    Cleaning Thermostat Housing Surfaces

    I am installing a new thermostat. My question is, How clean do the mating surfaces for the thermostat housing need to be? Do I clean the surface on the engine block to be shiny metal. I got the old gasket material off but it looks like it may be still covered with old sealant. I want to make...
  14. A

    Blink Marine Electronic Interface Module (EIM) Replacement

    Recently I contacted Blink Marine in Italy to ascertain if they could develop a replacement for the Electronic Interface Modules (EIM), Part Numbers: 1810628 (Forward) and 1970606 (AFT). A little background: Blink Marine brought the US supplier of the Sea Ray EIMs; however, Blink decided not...
  15. A

    Anchor Light Problem

    I have a 2011 Sea Ray 350 Sundancer. I have having problems with the navigation/anchor light. The front half of the combination light top of the radar arch does not light with either the "nav" nor the "anch" key presses. When the navigation button on the dash keypad the following occurs: The...
  16. A

    Reaching the Anchor Light

    I need to check the bulbs in the anchor light that is on top of the radar arch on a Sundancer 350. How do I on top to reach the light to check the bulb? The only thing that I can think if is using a ladder but don't know where I put a ladder so that it will not damage anything and I will safe.
  17. A

    Carling Switches or New Electronic Interface Module?

    I need to replace the Electronic Interface Module (EIM) on my boat. I am aware that I must replace the complete system because the original EIM is no longer available. What I have discovered thus far is that there is a replacement system that uses Carling switches with circuit breakers and...
  18. A

    Need Non-Operational Electronics Interface Modules (EIM)

    I am talking to an electronics circuit board repair company who thinks they be able to reverse engineer the Electronics Interface Modules for the 350 Sundancer. I am looking for any owners who have replaced their EIMs, who are willing to ship me with their non-working EIMs and non-working switch...
  19. A

    Port Switch Keypad Intermittent Operation

    The port switch keypad (PN:1797300) on my 2011 350 Sundancer works sometimes and other times it takes multiple presses to get the buttons to light up. This keypad was replaced by the dealer a year ago for the same issues. Very frustrating when running in the bay crossing shipping channels...
  20. A

    Engine Stalling

    I have a 2011 350 Sundancer with 377 MAG DTS Bravo III Sterndrive, Axius Joystick with about 453 hours on the engines. The last time I took my boat out, it started fine but the port engine kept turning off. It seem like the rpms would drop until the engine stalled out. Several times I was able...
Back
Top