Search results

Sorry, these are the screw on type mounted on the engine.

I also have a 94 and the fuel filters I have used are the following Fuel Filter · Quicksilver 35-802893Q · Sierra 18-7945 · Fram PS3808 · AC TP1239

Over the winter we replaced the salon floor and carpet, the forward search light, the cockpit side panels, and the rollers on the sliding door all using advice found in this group. I thank you all for your input. Now we are getting ready to take on our last project before the boat is put back...

I believe its from the wiring diagrams. Here are the three documents I have.

I know. Who does that when you can keep it in the front yard!!

Looks great! We are going to tackle one of the side panels this weekend. I'll post some pictures.

We found some rot is the port and starboard side panels and decided it would be best to replace them. What product did you use to replace the vinyl?

Thanks for asking but we have not. We have the fuel line, water hose, wires and exhaust disconnected. The lag bolts are out but we still can't get it to slide or spin. Looks like we have going to have to free up the bundles of cables in front of it and remove the battery. We are going to...

These are all of the pictures I have of the rotted section. Unfortunately we didn't take any pictures of the cleaned out area before we covered it. We picked out the large pieces by hand and then used a ShopVac for the little stuff. We used Marine 31 Mold Remover Gel for the final cleanup...

We finally completed fixing the rotted floor in the Salon. We discovered that the floor board did not go under the wall. They were secured together by a strip of fiberglass tape that was resin'd to both pieces. We took an oscillating saw and just cut the tape and the floor lifted up in one...

I replaced my dash last year. Flounder Ponder offers a complete set of replacement panels for the dash so I went with that because you could get the system monitor panel already etched in. I then installed three multi-function displays which allows me to have three functions up or switch...

That solved the problem. Thanks

Any ideas on how to remove the sliding door from the small stateroom on the starboard side. The hardware is loose and we need to tighten it up. We also want to remove the door to finish the carpet job (pictures to follow soon). Also, how do you post pictures so they are oriented...

I need to replace the water heater in my '94. I have read the posts on the subject and think we are going to go with the removing the manifold approach. The question I have is what did you replace the original water heater with? I've contacted a couple of dealers and I'm being told the unit...

Happy New Year to all!! I have a soft spot in the floor on the starboard side of my salon. I found that the three small oval windows were leaking which caused the problem. I removed and re-bedded the windows and have not seen any more moisture. I have already removed the carpeting. Any...

Thanks for all of the great tips and advice on my QS 7.5 generator. I think I am going to pull it so it will be easier to work on and try to see if I can identify the problem. I'll let you know how I make out. Here in Mass. the leaves are starting to fall and it was 41 degrees this morning so...

Thanks for the tip on the removal. Just brought it home last week for the winter. The generator will crank and run for about 5 seconds before it stalls. I was going to pull it and bring it to the local generator shop for diagnostics and repair. The cost to have them come out and do the...

One of my winter projects is to pull the original QS 7.5 generator out and replace it. Any suggestions on the best way to remove it?

I live in the Boston, MA area and had the same thing done about two years ago. I used the existing bimini frame work and had new framework made for the cockpit area. I too had to go to the only game in town and in this area they only work locally from May to September and then its off to...

Getting ready to launch in a few weeks and discovered that the hydraulic steering cylinder is leaking and needs to be replaced. Has anyone replaced their cylinder and what is the best way to get to it so it can be removed, replaced and bleed.