Search results

For Sale 2008 Sea Ray 47 (51' LOA) Fully updated and serviced 2008 47 Sea Ray Sedan Bridge with V-drives and 1180 hours. (no pods) This vessel is in great condition that has spent its entire life in fresh water. This vessel is loaded with almost every option available - Teak cockpit and stairs...

Congrats Zach! Someone scored a great boat.

I would estimate we are on a hook overnight 30-40 nights per year and always use a bridal. I've posted this in the past and it's held up pretty well over the past few years. All in cost about $100. I will upgrade it in the future with two separate pendants with stainless thimble.

Congrats! Looking forward to seeing some photos.

Keith, I use zinc but, boatzincs.com has aluminum and magnesium anodes for your "new to you" boat.

Main Engines - (2) sets: https://www.boatzincs.com/CumminsQSC-kit.html Trim Tabs - (2) R-3: https://www.boatzincs.com/rudder.html Hydrologic Lift - (2) T-20 Small Teardrop Zinc Anode: https://www.boatzincs.com/hull_bolt-on.html Hull - (1) B-24 Z24B Zinc Anode...

Could be your pressure relief valve on your hot water heater or could be the check valve in the pump itself.

I'm speaking from experience, if you are looking for a turnkey boat this is the one.

I had the same issue recently when I purchased my Highfield CL 310. I bought a 10ft length of vinyl dock rail and trimmed to fit my chocks. Here's the link: https://boatliftwarehouse.com/product/vinyl-4-75in-rubrail-5008/

Barney, I purchased Zack’s boat about two years ago and have been very pleased with the performance of the 47 DB. This boat is not a speed demon however, I cruise it 2450 RPMs (75%) which gives me about 20 knots. Those numbers take into account a fully loaded boat with approximately a 300 pound...

I assume it's a B-12 the same as my boat but, I will let someone else confirm. https://www.boatzincs.com/zc-406.html

I guess while I am posing Sea Ray drawings I should also include the "Drainage" drawing.

Hey guys, I had the power supply go bad on the refrigerator/freezer in the saloon on my 47DB. I reached out to Sea Ray to inquire how to remove the wood trim around the refrigerator so that I could unscrew the trim kit and slide out the refrigerator. I discovered that the panel in the attached...

Jeff, this is the diagram I based my opinion that it shouldn't be that difficult to change the pump. It took my mechanic about two hours to change the pump and I would attribute about an hour to the difficulty of accessing the starboard outboard pump. Post some photos and report back on your...

Or a Dentist in a Cirrus. :D

Jeff: I experienced the 2265 error code as well and had the Fuel Priming / Lift Pump replaced on my QSC 8.3 600 a month ago. Mine is a 12v pump and I'm pretty sure your is too. I ordered the pump from SBMR and had my mechanic replace the pump because, it was the starboard engine and a pain in...

Bobby, where do you keep your boat?

Bobby, I have a good mechanic here in New Orleans but, not sure if this repair would be in his wheelhouse. If he can't do it he may be able to refer you to someone else. Gene Hemard 504-437-0906.

I have not seen Zach's 48DA in person however, I purchased his 47DB two years ago which had almost the exact same upgrades. The quality of the installation of the updates and the condition of our sedan bridge was second to none. If you are in the market for a 48DA, do yourself a favor and take a...

Zach, if your 48DA is anything like the 47DB we purchased from you, there should be no problem selling it. I love both the N55 and the Selene 53 but, I need to see both boat in person to determine which on would be best for our needs. We are also including the Fleming 55 but, there are very...