Search results

  1. mattias

    2005 240sd carpet

    Hey community - I am looking for new (or used) snap in carpet for my 2005 240SD. Does anyone have a good recommendation or know of a quality member that can provide this?
  2. mattias

    Carpeting?

    It's a 2005...
  3. mattias

    Carpeting?

    We have a 240SD. Love the boat, but it's time for new carpeting! Has anyone replaced theirs and are looking to sell the snap in carpeting they took out?
  4. mattias

    240 Sundeck Thread - Questions and Answers

    Yeah, we were thinking about spraying the backside but since there are a few stains and such - we are just going to replace it instead...
  5. mattias

    240 Sundeck Thread - Questions and Answers

    I am looking for the snap-in carpeting (the backing is almost off on mine) for a 2005 240SD...
  6. mattias

    240 Sundeck Thread - Questions and Answers

    I LOVE our 2005, but I like some of the layout options of the 2011...
  7. mattias

    240 Sundeck Thread - Questions and Answers

    We have a 2005 240SD with the 350MAG (300 hp). We are looking at a newer 240. However, most that we are looking at have the Mercruiser 5.0 (260 hp). For those with the 5.0 in your 240SD - is this enough power?
  8. mattias

    Impeller change?

    I have a mercruiser 350 mag in my 2005 240SD - can I change the impeller when boat is in the water?
  9. mattias

    Navigation Light Bulb part #?

    Thanks all!
  10. mattias

    Navigation Light Bulb part #?

    I have a 2005 240SD. I need to put a new lightbulb in my port bow navigation light (probably replace the starboard one as well). Does anyone know what the actual part #'s are for those light bulbs? Can I get them at a standard auto parts store?
  11. mattias

    replace clarion xmd3

    I used those with my XMD3. Had no intention of replacing that unit if I thought it still worked. In any case put a new PYLE unit in since i thought the XMD3 went bad. I have 14.4 volts at the battery and my test light (shows power) on both the red and yellow wires. Still no radio? I am going to...
  12. mattias

    replace clarion xmd3

    OK - now I'm really at a loss and could use this groups expert help! I changed the Clarion XMD3 head unit since I had power at the head unit but it wasn't coming on. Swapped with a PYLE head unit since it had the AUX port that I needed (ant not a whole bunch of expensive stuff that I dont need)...
  13. mattias

    replace clarion xmd3

    I dont know that much about how single DIN units attach vs. double DIN units. Will a single DIN attach OK in a double DIN opening?
  14. mattias

    replace clarion xmd3

    They always find a way to "get" you! So, if I put in a single DIN head unit with an AUX input and connect that via a cable to my phone, would I be able to control the volume that comes out of my phone still? (I would just leave the volume all the way up on the head unit and just control the...
  15. mattias

    replace clarion xmd3

    I really like that Fusion unit but i really dont care if i have remotes or not - i can control everything with my phone... Will a single din head unit fit when i pull the xmd3 out?
  16. mattias

    replace clarion xmd3

    The head unit is a double din unit. The 2 remotes are oval. However, i am pretty sure they are round holes they are in. The unit im looking at fits a 3" round hole. Are the holes in my boat 3"?
  17. mattias

    replace clarion xmd3

    We have a 2005 240SD. It has the original Clarion XMD3 radio with 2 wired remotes (helm & transom). It looks like the head unit has quit working (the 2 remotes stopped working quite some time ago)! I have been wanting to replace this with a bluetooth unit anyway (streaming music from our phones...
  18. mattias

    Changed ignition - boat wont start now?

    on a 4 wire switch - is the "B" for battery, the "S" for starter, the "I" for ignition and the "A" for accessories?
  19. mattias

    Changed ignition - boat wont start now?

    I checked the kill switch a few times - it is in the "run" position. I also made sure that it was in neutral before doing anything?
  20. mattias

    Changed ignition - boat wont start now?

    Thanks! Couldn't agree more with the "ugly" terminations! Started to pull off old ends and put on all new crimped ends and shrink tube them, but decided to wait until I got everything back to where they needed to be. Unfortunately boat is now 5 hours away in its slip so I cant check the mfg...
Back
Top