Search results

  1. Jeff Adamsson

    390 roof support bars

    Thanks! We've decided to go another route than tear apart the interior. Short story is we removed the windshield, repaired it and have it reinstalled now. Everything else on the boat has been gone over and repaired or replaced, this was one of the last remaining items needing attention, and one...
  2. Jeff Adamsson

    390 roof support bars

    Hi all, we have a 2004 searay 390 and we have corrosion around the vent in the center windshield. We are attempting to remove Were t so it can be repaired. We have the glass sliding up out of the track but now we are hitting the window frame against the roof support bars. We have the top of the...
  3. Jeff Adamsson

    Mercruiser 8.1 engines

    I have for sale a pair of mercury 8.1 liter engines with transmissions from an 05 searay 390. The engines were removed last winter and replaced with a set of Cummins Diesels. The motors ran fine when removed, no overheating or oil issues. They have ZF transmissions mounted to them with 2.5...
  4. Jeff Adamsson

    Led strip lighting

    We changed the 4 lights in engine bay of the 390 to strip LED, and added one on each side, nice and bright. We then added 2 rectangle led lights to the bottom of the hatch and they really helped. This was in the shop with all the lights off
  5. Jeff Adamsson

    Updating a 390

    Thanks! We are going to find out soon enough haha!
  6. Jeff Adamsson

    Hello from Eastern Canada

    Nice, it is a bit of a challenge. So the boat came from Bedford and he is going to use it mostly in the Bras d'or lake, with trips to Dartmouth planned.
  7. Jeff Adamsson

    Updating a 390

    Thanks haha it was a pile of work. Nothing wrong with the 8.1s, the boss couldn't travel the distance he wanted without having to stop for gas, and around here it's difficult to get gas in some places and he was worried about the gas being a bomb. He is a diesel guy himself. He only owned the...
  8. Jeff Adamsson

    Updating a 390

    Once it's all day me and in the water I'll make a new thread for it showing all that I can, but I'll load some photos up now.
  9. Jeff Adamsson

    Hello from Eastern Canada

    Thanks everyone, I'm happy with the results so far. Here are a few more photos. The dash with the simrad installed, engine control panels, and the new control head in the mount I made up. It was a lot of work and as you can imagine everything was moved and adjusted. I also know where there is 2...
  10. Jeff Adamsson

    Hello from Eastern Canada

    yes, the trans ratios are now 2-1, we are running 1 3/4 aquamet shafts and new props as well tuned at 480hp now. Haha I agree, it was an expensive bit of work just to get away from gas. It was a good project though, Ill post some photos of the dash, and some custom work I put in, and whatever...
  11. Jeff Adamsson

    Hello from Eastern Canada

    thanks, yes, other than the final hookup of the electronics, everything was done ourselves
  12. Jeff Adamsson

    Updating a 390

    Hey everyone, New member here, I just made a post on the "who's who" page. If you haven't seen it, I am finishing up work on a 04 Sundancer 390, I converted it to diesel, new electronics, and alot of other work as you can imagine that went along with it. I would like to replace the rubber engine...
  13. Jeff Adamsson

    Hello from Eastern Canada

    Hello CSR! I'm Jeff from NS, and we are just finishing up the bosses boat. It's a 04 Sundancer 390, it had the Mercruiser 496ci engines and a Kohler gen set. We converted it to 6.7 Cummins and a Cummins gen set, so now he is burning diesel. It now has automaskin engine control panels and run...
Back
Top