Search results

"PASS_PGN=65030 PASS_ADDR=YDEG" Did allow the Genset data to show. Unfortunately the hours data is missing. I sent my config as well as log data to yatchdevices they said it looks good but they don't see hours data and said it must not be supported. I have emailed them back as the spec sheet...

I was just replying to the config. That's what I noticed was missing. I will give that a try tomorrow.

I have the the ISO_REQUEST=65242,65253,65260 in the config. In looking at yours I notice a couple things. I have the genset set for engine 2 on the nmea network. I was worried it might conflict with the other engines. The other thing I notice is PASS_PGN=65030 PASS_ADDR=YDEG

I set the engine address as 234 which is the default for mine. Also I cut the jumper on the nim to transmit J1939

I figured out the data issue. On the 703 I had to go into devices then yatchdevices then the config button. inside the config menu there is a config instance and is generator data source "auto,on,off" It was set to auto I changed it to "On" and now I get the basic engine data. However no...

That is what I see as well. I have been going through the 703 manual and don't see anything besides the enable feature. I tried the auto select but no different, the yd appears in sources menu on the vv but that is it.

That's strange I don't have that menu. If I go into mercury feature settings genset is enabled, however I am unable to select a source anywhere. Genset shows up on the left bar menu however no data. I am not sure the yacht device is sending the data correctly. On the vv sources I see the...

Did you need to do anything to the config either in the vv703 or the YATCH devices in order to get it to see the data? I see data from the yatch devices but nothing on the vv703.

Thanks great info! It looks pretty straight forward. It looks like my boat was wired a little different as my genset has a cable running directly from the genset to the smartcraft jbox it is not tied into the engine harness. So I will just take if off the jbox and wire up a connector for the...

Did you use a custom config on the Yacht Devices (YD) YDEG-04 or just the default one?

Yes the VV was powering up and was on the nmea network. The 84M0076067 will supply the power through the power plug. The VV link was not powering up. The smartcraft end of the 84M0076067 cable should have power however it did not. It is made for the VV7 which has the VVL integrated inside it...

I have figured out the issue after I cut apart the 84M0076067. The cable is not compatible with VV702 or VV703. These cables came direct from https://sbmar.com they are supposedly experts and you would think they would know better but obviously they don't as I called called them and they told...

The 84M0076067 cable comes with both connectors. One for the vv7 and one for the vv link. However ttmott got me thinking that the problem may be in the way the cable is getting power. In looking at it the vv7 and the vv link they are not getting power from the same pins on the plug. The...

I will try to trace the wires in the loom. This is the smartcraft connector I have. Not sure where the CAN P crossover cable would be. It looks like in the wire harness that as you said "A" is Battery positive "B" negative and "F" is switched key Positive

I am not sure the link documentation doesn't say. I had thought it was getting its power from the vv connector. I know the nema network is good as I see all the devices on it. However the link device will not show up unless I use the connector that came with the kit not the 8M0075065 & 8M0075067.

Hello, I know this is an old thread however I am having some issues. My conversion is a vv1.5 to vv703. I am using cables 8M0075065 & 8M0075067. For some reason I am getting power to the vv703 however the vessel view link is not receiving power. I can plug it in with the kit cable and get...