Search results

  1. Lenny3

    New Steering Wheel

    I’ve search for over a year for a steering wheel. I found a few I like, but I just couldn’t pull the trigger. I seen this one on eBay and I couldn’t be happier. Very well-made from stainless steel and hand sewn leather and at $85 I couldn’t pass it up!
  2. Lenny3

    Water manifold

    These things are NOT cheap and NOT fun to change! While changing my float switch I notice it dripping! While I was there it changed it.
  3. Lenny3

    Extended Mercruiser flush ports

    Extended my flush ports to my rear electrical cable storage area. My boat is in a slip 365 and sometimes is not used for a month or 2. Thought I would flush with Salt Away or some other product while not using. I’m not planning on closing the sea cock as it’s a pain to reach. Fresh water and...
  4. Lenny3

    07 310 sundancer cieling sag

    My ceiling is sagging on the port side near the skylight over the galley sink. Where are the fasteners that hold it up and what do they fasten to?
  5. Lenny3

    1st haul out

    1st haul out and was expecting a bottom paint job but it looked great. Compound buff and wax below the rub rail, install new speedo paddle wheel
  6. Lenny3

    Falcon Heavy Rocket

  7. Lenny3

    Flooded Helm

    During the last 2 hurricanes I removed the canvas so it didn’t get shredded. This created another issue that I just found. The area below the helm filled with water high enough to partially submerge the DC fuse panel. Found out there was debris blocking the drain holes on each corning on the...
  8. Lenny3

    What the heck is it?

    Seen this on FB …
  9. Lenny3

    Watcha get from Santa?

    I got…I got a Garmin Auto pilot thing witha witha Octopus pump and allllll the stuff to make it work!
  10. Lenny3

    Shaft seals 2007 310

    So it looks like I will be replacing the Tides Marine shaft seal on the 310. I do have a spare seal on both shafts. (Port/Starboard) Question is, has anyone ever successfully completed this job and if so, what all did you remove to gain access to them? Looks to me like removing both exhaust...
  11. Lenny3

    DIY Dry Bilge System

    Always had water in the bilge between the engines on the 310 so I decided to take a shot at a DIY project I seen online. I plan on plumbing it to the shower sump. I’ll install it over the Thanksgiving weekend and report the results.
  12. Lenny3

    Depth transducer

    My depth indicator in my Smartcraft gauge works for the first few hours then it will flash the last depth. Could this be a failing transducer or smart craft gauge?
  13. Lenny3

    On the Halifax after Ian

    Had the boat out on the Halifax on Wednesday. Water was high and dirty and a few pieces of debris but not bad. Spent the night on the hook near the ISB Bridge. Nice view of the bridge.
  14. Lenny3

    Daytona Beach Boat explosion

    Happened at Halifax Harbor Marina
  15. Lenny3

    Abandoned boats in the Halifax

    Finally removed some of the abandoned boats from the ICW near Daytona Beach. This one and 4 more behind it were in the water for at least a year.
  16. Lenny3

    Fender cover

    Bought these fender covers from Amazon, 2 for $28.99. Seems like a quality product and a great price. I’ll report on how they hold up.
  17. Lenny3

    Corinthian marine install

    I wanted to try something different than the EVA Foam so I decided on Corinthian Marine vinyl weave. Quality was good and the fit was perfect.
  18. Lenny3

    Afternoon on the Halifax

    https://share.icloud.com/photos/006ZggJlcsOXtOYbM2sd8Mf0A#Daytona_Beach
  19. Lenny3

    Smartcraft LCD replacement

    I’m sure this has been covered here before but I wanted to let anyone know that’s thinking about replacing theirs that it’s rather straight forward and easy. You can find the LCD screens on ebay.
  20. Lenny3

    No power to vacuflush pump

    Head Breaker is ok, (removed panel and checked for DC voltage on both sides of breaker). No power at + side of pressure switch. If I add 12v power to + side of switch the pump and pressure switch runs perfect. Where does power wire go after is exits the breaker?
Back
Top