Search results

Hi All. We have outgrown our boat so we have listed our 2005 340DA on Boat trader. If you know of anyone looking for an extremely clean Sundancer, Please shoot me a message. I really appreciate everyone's input on this forum. I'll also be posting it on clubsearay classifieds soon. Thanks, Randy

Switching to LED bulbs in the cabin. Can someone please tell me which bulbs are needed for the cabin ceiling lighting? I did a search on the forum but can't find the exact replacement info. I'd like to replace the stock bulbs for LED's in the small round fixtures and the 2 larger round...

I figure that the previous owner may have installed it so it could be kept on a lift. just another place for marine growth to hide out.

We have a 2005 340DA. does anyone have a Jabsco check valve installed on their A/C water line intake between the seacock and strainer? I was having water flow and cooling issues so when I found this, took it apart and it was clogged with barnacles. thinking about removing the check valve...

yes, I had this happen to me and it pulled one of the mounts away from the hatch lid. My problem was the switch pad going bad so I Suspect, yours is the switch pad and not the hatch motors.

Hi All. We have a 2005 340DA. We want to replace our stock Clarion receiver with a Fusion unit, replace cockpit speakers and add a sub. Has anyone with a similar year 340DA completed this install and be willing to share some details/pics with me? What size sub did you install and where? Would...

Thanks Kevin. Are you happy with the Raymarine? I'm not sold on either Garmin or Raymarine, I just have lots of friends here in South Florida that have all gone to Garmin. Looks like the 12" unit would fit where my Vessel view is installed but that just makes my project even more time...

New Garmin GPS Chartplotter question for my 2005 340DA It's time to retire my Raymarine E80. The unit still works along with the radar, it's just not user friendly and lacks bells and whistles. So my question is, I'm leaning towards the Garmin GPS Map 1242 or 943 and I'm curious if anyone has...

I like the new system. Their instructions were spot on however, I recommend having some help when it comes time to run the new wire bundle from the bilge to the helm. The system is very expensive but I got tired of only being able to use one side at a time since both switch pads work but only...

I just replaced my entire system with the FP marine EIM panels. I have entire system for sale. May list on EBAY also. Will post pics in a new thread soon. Both switch pads worked when removed however, only when one was connected at a time. When both were connected, they wouldn’t work which...

I will be selling my entire system once I install the new system. Hopefully be early next week.

I was able to get mine repaired for $20 at a local fabrication shop here in Boca. installing it today. thanks

Well, it appears that both my switch pads work fine so my problem is with the eim box itself. I bit the bullet and ordered the retrofit kit from FP marine. I’ll be listing both my switch pads for sale once the install is complete. thanks for everyone’s advice. Hated spending that kind of...

I’m searching for the actuator mounts that are attached to the underside of the engine hatch. The ones that the rams mount to for raising and lowering the engine hatch. Please let me know if available? Thanks

Tried some of that already. not sure how those actuators pull so hard. This steel is extremely hard. I can move it with a 3lb sledge.

Yes, I’m working on that also. found the part number for the newer model Sundancers so looking for a clear picture to see if that bracket will work on my boat.

Hi All. these pictures are what happens when you can’t stop your hatch from closing with the safety kick stand down. My EIM failed and caused the hatch to lower on its own. I just happened to be unable to stop it before it bent the upper bracket from the bottom side of the hatch. Question...

Update. Spent some time yesterday troubleshooting our problem with the EIM. Found that when I disconnect both switch pads from the small bus under the helm, reinsert just the left switch pad, the left side worked as it should. Tried just the right side and it may work for a few seconds and...

Pyro, YES, both panels,L&R, have a small wire bundle that plugs into a box like the one in your picture. Then, there’s another plug that goes out somewhere but haven’t had time to chase where that wire bundle goes to. It’s like a junction box or bus of some sort. This is a new problem and...

thanks for the info. I’m just curious as to why both side would go out at the same time? It’s not just one switch, it’s all the switches on both sides at the same time. But they seem independent of each other. I was able to trace the wires from each side to a bus of some sort under the helm so...