Search results

Re: 410 Sundancer/Express Cruiser and 400 Sundancer/Express Cruiser **Official Thread Hi guys: I recently did a 1999 400DA in MarineMat. I have the template for this boat and can offer reasonable pricing to Club SeaRay members. I'm in the Tampa area and offer installation also if you are...

MarineMat Swim platform pads are available for 1998 - 2002 310 Sundancer. Very reasonably priced, hundreds less than others on the market, Easy peel and stick installation, teak plank look or 24 other color / designs available. Three year limited warranty. MarineMat is an Original Equipment...

Hi Mike: Thanks for the information!

Hi: MarineMat, like Seadeck, is a closed cell EVA foam product. MarineMat is custom cut for each application by CNC. Both product have a 3 year limited warranty. Side by side it would be very difficult to see a difference. As a dealer for and a user of MarineMat, I find the product to be...

Hi: I was actually focusing on swim platforms but I do have a complete cockpit drawing for that generation 340. There are some variables. The helm seat pedestal is installed by hand at the factory and placement can vary. The rear cockpit table pedestal, same concern. There are two "reliefs" for...

Hi all: I am a MarineMat dealer/installer in the Tampa area. I now have templates drawn for the following SeaRays: 1998 - 2002 310DA, 1999 - 2002 340DA, 1999 400DA (upper & lower). I can offer much better pricing on these models than you will find on websites. We can do teak look or select...

Hi! I am a dealer / installer for a similar product, MarineMat. I have found that even on the same model and year of boats there are sometimes slight variations in the dimensions. Using a "previously acquired" template will get you close, particularly on the overall dimensions, but placement of...

This is a recommendation based on my experience. I replaced my manifolds and risers on my 350 Mag MPI's three years ago. I decided to try GLM based on their pricing. The old Mercruiser parts were 8 years old and upon removal the showed no signs of failure so this was strictly preventative...

I did replace the water heater once after the salt water connection ate it away. That still would have been about 6 or 7 years ago. I did not reconnect the engine hoses to the water heater. We just "rough it" while cruising. The gulf water temp is upper 80's lower 90's so even the "cold" water...

I bled the hw heater per the mfg instructions: open the nearest faucet and open the pressure relief valve at the same time. Also, yes, all 3 hot water faucets are weak. the swim platform shower, the bathroom and the kitchen faucets. Yes, I did remove the strainers and they were clean. Also the...

I have an unusual problem (I think). Its a 2002 310DA but the same ShurFlo set up as ususal. I have very little water pressure on the hot side. When I turn on the faucet I get a burst of pressure which then turns into very light flow and then a trickle. I thought it was an air pocket in the hot...

Hey there: we tried running out of Hurricane Pass Sunday evening just after low tide. We were stuck inside the marked channel also. Maybe that's why there are no intermediate markers over such a wide span. Maybe some sort of warning would be in order. It makes you think about how many other...

I have a 2002 310DA with 350 mag mpi v drives. Boat has been idle for 3 months. Turn on ignition and no warning horn sounds. Also no audible fuel pump pressure up. Engine cranks won't start. Same situation for both engines. Turn starboard ignition on and the auto fire extinguisher light goes on...

I have had a 2002 310 DA for the last 8 years. It is an outstanding and reliable boat. I have had minimal problems with it. My recommendation is to do as much of the maintenance and repair work as you can, yourself. No one will do a better job than you. The only repeat problem I have had is with...

I replaced the Clarion with an Alpine unit to allow me to use the iPod feature on my iPhone. I also added 4 Polk speakers to the cockpit and 2 JL speakers to the cabin along with a powered sub. I cut the new faceplate and trim bezel from stainless steel and maple. I also cut and inlaid the Sea...

I have a 02 310DA w/ twim 350 mag mpi & vdrive. Two weeks ago the boat ran fine, a little stumble here and there but it cleared up & ran well for the last 1.5 hours. Last weekend the starboard engine would not go over 2300 rpm & consequently wouldn't plane off. Nothing was added, changed or done...

Hi all: I just wanted to post a radio installation I just finished. I finally got rid of the Clarion and put in an Alpine so I could use my iPhone. Whatcha think?

Here is the installation with the trim ring.

thanks! i tried to add the picture with the trim ring around it but, as you see, I failed.

I replaced the Clarion radion in my 310DA with an Alpine CDA 9884 primarily to be able to access iPhone music. To do it I cut a faceplate out of brushed stainless to hold the radio and cover the old CD changer hole. The mounting holes line up so I can reinstall the old set up if I need to. I...