Search results

Has anyone had this problem? This seems like it's a Sea Ray issue I thought I read a simular post but can't find it.:smt013

What are other 310 owners using for 2nd ground tackle and where to store.

How difficult is the shaft removal from the ZF trans.? Is there a special puller needed to remove the shaft flange on the trans. end. I need to pull the shaft because some moron probably at the Sea ray factory put the spare Tides seal on backwards.

I just went to replace my leaking seal on my port shaft. When I opened the carrier seal, I found that the seal was installed backwards on the shaft. So then I checked the starboard seal, and that was also on backwards. Now I'm wondering if this is Searay issue since these spare seals were...

Can anyone recommend a good marine mech. in the Mystic,Groton,Newlondon area. I need the prop. shafts pulled to replace shaft seals. Thanks

I noticed a small leak where the ball valve meets the hull. This is the on the AC discharge line in the FWD berth above the water line. I'm guessing I just need to rebed the fitting from the outside. My ques. is does the fitting unscrew from the valve from the outside? 02 Sundancer 310...

Here's my dilemma. My 01 310 has the original Lorance 3500 digital depth sounder. I've just purchased a Raymarine chartplotter A70D. So I can remove the Lorance transducer and enlarge the hole for the A70 or drill a new hole next to it and have two sounders. Will the transducers work being...

Just purchased a 01 310 dancer last nov. Bottom has Pettit Ultima on it. Bottom only needs touch up but the struts,rudders and trim tabs also have bottom paint . On prevous boats I kept most metal parts bare. Should I remove the bottom paint from those area's?

Looking for the full factory manual package for my 310. Bought the boat as a repo. no manuals. Already downloaded the online version. But I'm sure the briefcase package from the factory contains much more. Thanks

I'm installing a new Raymarine A70d chartplotter/sounder to replace my Northstar that's dead. I need to replace my thru-hull transducer with the correct one for the A70. Is the deadrise 23deg? I found that on the 310 spec. sheet. I just want to be sure. Thanks

Are these original TV antenna's of any use? Will they work with these new boxes that they have for home TV. If not I'm going to take it off my radar arch.

I just purchased a 02 310. It came with radar and sat. TV mounted on a ridiculous comb.mount. Anyway I'm not reinstalling the sat. TV and would like to mount the Radar dome back on the arch. My ques. is does the arch have the 4deg. angle molded into it where the dome mounts? It looks like it...

I have a 02 310 with a Norticold fridge. I looked at another 02 that had a different model. It looked like it might be a little deeper and had the t-stat on the outside. What is the difference?

Is there an additional step to winterize the injectors? Talked to a MM he sail that he runs an additional fuel conditioner thru the injectors some how to lubricate them. The fuel in my tanks have already been treated with sta-bil. I don't see why running that thru the injectors will do. Any...

Just purchased a 02 310 with a Sea-Tel TV dome. Also included is radar,anchor light and Sat dome mount. Anyone interested?

I just purchased a 02 310 dancer with a Kohler Gen. It ran fine during the survey. Since then I've had trouble getting it running. Today I put 2 new plugs in and a Fuel filter. It started and ran fine. I ran it for 10 min. and shut it down. I then went to start it later and I'm back to same...

Just took delivery on my 02 310. I plugged in my shore power and only have 63 volts at the main breaker in the cabin. I have 130 vac at the shore power outlet and breaker. Is there another junction point between the transom conn. and the main cabin?:smt100

Port engine shaft seal is leaking on my 310 v-drive. I was told the the engine has to be pulled. Has any one done this without pulling the motor?

Does any one know where I can get the operators manual for the Clarion system on my 02 310?

Where can I get the cushions the fit on the aft cockpit table on my 02 310. Thanks, Dave