Hello this is my first year with “my” new 2005 290 AJ it has twin 5.0 mpi’s. I’m winding how my fuel use compares and if I have any sort of problem. Boat is running great and seems to be normal speed for rpm’s etc. at 32-3500 rpm’s I’m going around 25-28 mph. WOT I’m getting 4200-4400 rpm’s and...
I have a 2008 Sea Ray 220 Sundeck and the Speedometer, trim on the center gauge, and digital led screen on the tachometer (not tach) all went out suddenly while boating last weekend. Otherwise boat ran great had no issues. Ive checked all the fuses visually and with a multimeter, none are bad. I...
Does anyone know what cable Sea Ray used in 2005 for connecting the smart gauges to the engine. The Sea Ray part #1727449, I can't find it anywhere. The diagram shows 1 inline resistor at the motor but Mercury needs 2. Did Sea Ray use a cable that used a resistor at both ends? The reason for...
Hi All,
I've got a fault 32, calling out starboard exhaust O2 sensor- There's two on each side. Is there any way to determine from that code which one on the starboard side?
Thanks,
-Gerry
I just bought a 2021 Sea Ray SPX 195 with the 250 HP 4.5L. This boat has Smart Craft module & Vessel view with a Simrad GO9 MFD. I was wanting to get Smart tow to be able to work on my boat. It is enabled on the Simrad but just doesn't turn on. What's weird is troll mode works just fine. But I...
We have a Smartcraft on our 2008 Sundancer 44 and the gauges were a bit off when we bought the boat in March, but then we had it washed and now the gauges and display are not working, along with the skyhook. Anyone have any advice on what to check or how to reset?
Hi guys i have recently purchased a 2015 Sea Ray slx 210 with a 350 mag and bravo III , it also has the dts electronic shift and throttle . This boat only has 24hrs on it . I was on the water today and at higher speeds the gauges will beep , do a sweep and at the same time the boat will go into...
Hello all. I'm new to the site. A master reset was done on MY 2004 280 Sundancer by the dumbass owner (smh) and now the fuel gauge does not work. I took my boat in to a certified MerCruiser mechanic who was able to get all the other gauges to work again, thankfully, but not the fuel gauge...
I think the next addition to the 240DA will be integrating SmartCraft into my Axiom-9. I have had a few scares when 17 year old gauges decide they are tired and indicate zero oil pressure and such while underway. I have also had a couple mystery alarms that would have been not such an issue to...
I have installed the new VesselView 4 inplace of the Smartcraft sc5000. All items appear to work on the new unit, but the Smartcraft analog gauge does not work for the fuel only. All other parts of the analog gauge are working. I can see fuel level on the VesselView. The fuel level was working...
Hello All,
I ran into a no power connection on dash gauges for my 2007 240 Dancer 5.0 MPI Bravo III.
I was out on the lake all day the weekend before, got back to the slip without an issue. The following Saturday I went to start up and was not receiving power to the smart craft or any dash...
Hey guys I am getting ready to do a overhaul on my boat and I am hoping someone can confirm that what I am planning will actually work. I am getting ready to put a SmartCraft network in my 2004 Sea Ray Sundancer 320 w/ 5.0 MPI I/O engines so I can get my engine data on my MFDs. I have a...
Hello,
I just finished sea trial on a 2004 320 sundancer. I found out during the sea trial the" Vessel view" is not working. Is this a module that is one part of the whole system? I spoke with the local Sea Ray dealer and they told me it could cost up to $2200 to replace. Has anyone had this...
Fellow Sea Ray owners, my 2006 Sundancer 320 has a chronic issue with sensor alarms causing Guardian mode to initiate, and one or both motors shut down (Merc 35O MPI)? Shutdown occurs at low speed. All gauges normal. Had mechanic replace port oil pressure sensor, and stbd water pressure...
This week the three gages on my 2006 Sundeck 240 instrument panel all quit working, with the exception of the tachometer analog indicator. The instrument panel quit working while I was under way. The panel consist of three gages, from left to right. 1. Analog speedometer 2. multi gage with 4...
Did my survey and everything looks great at this point. few things came out before the survey report. SR310 - 2008 with 6.2 seacore and AXIUS.
Engine data not showing in GPS. newly installed Garmin 74CV + Transducer. How do i get the data form the Smartcraft to the display on the garmin...
Hello Crew,
I just purchased a 2014 Sea Ray Sundancer and will have it next week (can't wait :D).
My current boat is a Chaparral 290 Signature with Garmin Chartplotter and Auto Pilot and I am enjoying all the features like Auto Guidance and automatic Auto Pilot engaging from my Garmin setup...
I recently replaced my SC 5000 with a VesselView 502 on my 2006 44SD with twin 8.1's. The only way to power up the VesselView is to have both engines ignition turned on, engines don't have to be running. I have a friend that has a 40SD and his gauges and SmartCraft/VesselView 7 are wired to...
Hello guys
I have a couple of questons. Hope someone here know the answer
1: I have a 2006 sea ray 280 sundancer, Merc 496 Mag (375hp) w/ bravoIII. What ratio do I have on my bravo III?
2: My transom assembly is not in good condition. Do I have to buy a Bravo Magnum transom assmbly or will the...
Hi All,
I have a 44 Sedan Bridge (2008). What is the normal range for the rudder indicator on the Smart Craft display? I'm showing 20 to 20 degrees lock to lock. The indicator goes up to 60. I don't know that I've ever paid attention to this. Is 20 degrees normal?
Thanks
Chris