I am looking to add a junction box to my helm in order to simultaneously run my helm smartcraft guages as well as Mercury VesselView Mobile. Currently, my 10-pin engine harness runs directly from my engine into my Tachometer (the tach has a small digital display for smartcraft data).
Can I...
Recently purchased a 2012 Sea Ray 240 Sundeck ant the Smart Craft Gauge says Sys Fault OBD service soon. When cycling thru the different features Trim, RPM, Water PSI, Hours , Engine Temp they all work and report accurate readings. However Depth & Water Temp are not working. Prior owner had...
All, I received this error/alarm this weekend. The engine went into automatic protection mode at this point. The engine runs smoothly and sounds fine to me, but I'm not a trained mechanic. Is this an ignition coil issue? If so, wouldn't the engine sound rough?
If your gauges are starting to fail, or just have cracked lenses, I highly recommend GaugeSaver in Green Cove Springs, Florida.
They saved my Smartcraft Tach with multi-function LCD/ and troll control. It had been acting very strange, intermittently, without any rhyme or reason. Totally blank...
I'm having an intermittent issues with the Starboard gauges and center shared gauge on my 2005 280 Sundancer with twin 4.3 MPI's. I was anchored for the day on Saturday. I was running the generator (runs on the same battery as the stbd engine) and it started just fine multiple times. I ran...
My display on a 340 2007 Sundancer is very weathered and hard to read. Can the plastic be replaced or do I need to upgrade to Vessel View? I am actually looking at purchasing this boat with this Smart Craft in this condition what are my options?
Day number one on this site, my current boat is...
I have an '04 240 Sundancer with the Mag 350. So my fuel gauge and speedometer are not working. They worked at the end of the season last year. On the first startup this spring they weren't. I replaced the sending unit. The fuel gauge is the last gauge in the order. The speedo is next to...
Hey guys I am getting ready to do a overhaul on my boat and I am hoping someone can confirm that what I am planning will actually work. I am getting ready to put a SmartCraft network in my 2004 Sea Ray Sundancer 320 w/ 5.0 MPI I/O engines so I can get my engine data on my MFDs. I have a...
Anybody know where I can get the analog speedo and tach gauges along with the smart link SC100 gauges to go with it like volts, water temp, fuel, oil psi and water psi? Mine don't have any LCD readout or buttons to push.
I have the little small 2" Smartcraft SC1000 monitor display unit and it...
On Sale now: EBay item #223003651215
Lightly used. Only on SeaRay 420 for 4 years 2007-2011. In perfect readable condition. Includes initial start up guide & wiring harness. Easy install- plug & play.
I have a 2012 Sundancer 370 and encountered an odd event when I boarded this weekend. My routine, like many is to go down below and flip the 3 DC converter switches to power up the cabin lights etc...when I flipped the port switch, no lights came on but the port engine tried to start! My...
Price $2,400
New in box MerCruise SmartCraft Transom
Part Number: 6315002TP
Was purchased for an 8.2 L MerCruiser Bravo 3
Located in Oxford, Maryland
Buyer responsible for pick up or shipping costs
Fortunately I have twins and made it back to dock without a tow! After a couple of hours of successful cruising yesterday, I move the throttles from idle to power up, and just before achieving plane, the port motor quit completely. The smart craft screen for that side went dark and the analog...
I'm having a nagging problem with my fuel gauge, both analog and SmartCraft (they have always matched, so I know it's not the gauge itself). I have a 2007 240SD with 350 Mag. Last year, both indicators went dead. However the GPH and gallons used still worked, so I finished the summer always...
Mercury NMEA2000 Gateway Part #8M0065208 that allows you to push the engine info out from the Smartcraft system to your NMEA2000 network and get the info onto your MFD. Works great, I used it to push the info to my Raymarine E95. The new Vesselview has a NMEA2000 connection built in so no need...
I upgraded to the new Vesselview 7 so I have my systemview screen and wiring (to the J-box). It operates good and screen is in good shape. I am looking for $450 plus shipping. Please PM me and I can send pics.
I also have the Mercury NMEA2000 Gateway Part #8M0065208 that allows you to push...
I have an issue with my port tach and am considering replacement. The analog guage is inop intermittantly (reads zero or low), but the digital display is constant and correct. This leads me to believe it is a mechanical/electrical issue in the analog guage itself and not an engine or...
Hello: I recently bought a 2003 240 SunDeck with Mercury SmartCraft Gauges. The cluster has a square LED monitor in the middle and 6 round tradition guages. The guages were working fine but becuase I just bought the boat I wanted to reset a few of screens in the SmartCraft Monitor like fuel...