I have complete 2005 260 Sundancer Bimini tops , Side curtains and rear camper top. Color tan all in great shape. Canvas only no frames .Some of the pieces were replaced in 2008. I recently replace all the canvas on boat. fits 2005 to 2008 260DA Bob 603-233-0787 E-mail Bajabob1000@yahoo.com can...
I have complete used 2005 tan Bimini /camper and all side curtains for
2005 Sundancer with radar arch rear camper was replaced in 2008 Canvas only
great shape . can e-mail or text pictures
fits 2004 to 2008 260 sundancer
Bob 603-233-0787
$500.00
I have complete tan bimini and camper top set and all side curtains for 2005
260 sundancer fabric only no frame . great shape no rips or tares
$500.00
call Bob 603-233-0787-
can text pictures
I need help most of the snaps on the side of the boat for the canavas were drilled at an angle from the factory kind of sloppy job, so the snaps do not go in flush or fit snug to the hull . How and what would I use to fill the holes. keeping in mind I need to drill in the same hole to reinstall...
Hi Any body install a bow roller on 2006 to 2012 240Sundancer
if you could you post some pictures. or a close up picture of anchor
roller on a 260 Sundancer may due.
Thanks
Hi need favor looking for picture of the back of vacu flush toilet
on a 2006 to present 240 Sundancer . Converting my boat
to vacu flush. Would like to see details on the factory set up.
No one in my are has one to look at. also if you can some
pictures of the holding tank :smt001
Thanks Bob
Hi looking to install toilet /vacu flush head system
could some one tell me if the head/toilet discharge hoes comes out of the back
of the toilet or under. If some with a 240 could take picture of rear of toilet,
that would be great .:huh:
Hi has anyone installed complete head system. I have a 2008 240 Sundancer with pump out head.
Looking to install complete head system with toilet,holding tank and
macerator pump. :huh:
Hi
I am replacing a section of my rub rail not ss part but vinyl part that ss is attch to on my 240 Sundancer.
Question is when I remove The pvc vinyl part that is attch to the boat do I
just use the exciting screw hole's or should fill them and re drill,
and what would I fill the holes...
Doing some engine maintenance today and noticed that the plug for the
mercathode located behind engine a two prong plug with label
MERCATHODE but not connected to anything and can not find were it should plug into
could not find its femail half any were help
it is the...
:huh:Question 240 sundancer 5.0 merc engine at idle can here what sounds
slight exhaust leak is this nornal I work in the automotive field and know what
a exhaust manifold leak sounds like my truck manifold starting leaking when its cold
so before i go and repl manifold gaskets is it
normal...
I have been trying to trace the source of a water leak on my 240 sundancer
the floor in front of the frig is getting wet . My questions is the frig
when running must make water or some condensation were is the
water spose to drain to i pulled frig and could not find drain tube or
see were...
:huh:Any one have water leaking from the refrigerator
after running frig rug just under frig on floor all wet
what is strange just the bottom of the rug is wet if i run my hands up the side carpet
that part of the rug is dry, just the botton of the floor.
cant seem to find source of leak...
:huh: Hi
Bought use 2008 240 sundancer iam looking for the short pole
that goes under the table when you use it for the filler cushion.
I have the long one for when you use for the table .
any body have pictures
or can tell me were i can buy one
Thanks BOB
Went out and boat my boat cash made for easy purchase private sale and was able to get good deal .need to now who will finace
my boat need to put the money back in my IRA
trying to go thru essex but wow 3 weeks and still no answer
and screwed up my aplication very hard to deal with never...
Dumb Question just bought 240 sundancer
not sure how to set up vee birth center cushion
I put the table top to fill the opening then put the
cushion now if i move around table top slipps out.
i did find an white platic thing that looks like it should
go across some how but does not fit...