Search results

Sorry, Sold It was replaced with a custom table Rich

I've done mine with 1 Gallon but it's tight. If I remember I skimped at the end and may have thinned remaining paint to complete job. My exhaust, rudders, prop shafts and trim tabs are all painted which adds to my usuage. I have always used Petit Hydrocote black, and have been very happy. The...

KevinC thank you very much for the detailed response to my question! I may reach out to you Presently I'm just trying to add piping in my cockpit seats only ( backs are fine) Don't even know if I can do it!! I do have a sailrite machine haven't taken off the vinyl yet but what causes it to have...

I have a 2005 320 Sundancer, can anyone help with upholstery manufacturer and color? My seams are breaking down on my cockpit cushions and I was looking in to redo with a vinyl piping to match ??? Some older Sundancers have used this piping and it appears the seams hold up much better. Anyone...

Cockpit table from a 2005 320 Sundancer, excellent condition. Pick up or meet Baltimore/ DC area $100.00 Call/text Rich 240 381 3903

Don't want to hijack this thread, but I have similar slow starting issues on my 05, 320 MAG MIE Horizon -- Just checked my Mercruiser manual and I don't see the above starting procedure. Please help as to where this is located Thanks Rich

I have replaced my fuel senders with KUS and I am very happy. The starboard tank uses a 21" length, the port takes a 20" sensor. For ease of installation I cut a 6" hole in base of port side lounger just above fuel sensor and made a hatch removable access door for future work. The job is quick...

Does anyone know the color and manufacturer of the vinyl used on the cockpit seats? looking to purchase matching vinyl piping to repair seam splits Thank you

Installed new electronics and looking to sell functional E80 with Navionics east card. Bezel and dust cover in excellent condition along with working unit. No cables Text Rich at 240- 381-3903 Looking for $250.00 plus shipping if we cannot meet

Was that part # 8M0156229? Anyone know what that does?

I have both switch pads and EIM’s for sale. I replaced the entire system with Flounder Pounders. I believe the port switch pad was going bad. The port side had no power to any function but if I tapped it, power would come on and all would be fine. Sometimes it worked perfectly. These came from a...

Does anyone know if both fuel pumps can be replaced in a cool fuel 3 module without removing the module from the engine. This is the port engine on a 320 with 350 mag horizons 2005 Thanks Rich

I have a complete set of Black canvas for a 2005 320 ( same as 2003) if interested. Check my post in classified for pictures and contact info Rich

Still for sale if anyone is interested!

I don't think it's the injectors as the starboard engine have been replaced. It is both engines that have the same issue, do other owners of a 350 mag have similar issues??? The cool fuel module has been replaced on both engines and I did notice sludge ( dissolved paint ) around the regualtor --...

I have had this problem since I owned this boat. The engines are 350 mag horizons, and the issue is that if the boat sits for a few days they have to crank for 5-7 seconds before they start. If I just energize the fuel pump 3 times by cycling off the switch it appears I pressurize the rail and...

I have a similar problem on my 350 mag horizons mpi. On starting, mostly cold engines I have had success by turning the start switch two or three times to presurize the rail. I never knew there was a fuel pump check valve, does anyone know where this is loactaed? I do have Cool fuel 3, and have...

The cushions pictured are not from a 320. I believe they are a representative picture of what the original poster is looking for Rich

I have a brand new cushion from a 2005 320 that has never been used. If interested text me 240 381 3903