Search results

Can the muffler remain in place or does it have to be removed in order to change out a Gen 3 cool fuel module on the port motor. ALSO,does the exhaust manifold have to be removed. Any tips on this would be greatly appreciated.

I owned an 04 320 with the 350 mags. The boat will cruise at 3500 rpm, however, the performance will increase if you change from the standard 3 blade props to 4 blade 18x18 DQX.(They need not be nibral.) the boat will jump out of the water quicker, and performance will be 1 mph less at the top...

Can you check the transmission fluid level when the transmission is cold?, Is dextron iii ATF the proper fluid to use/fill the transmission?

I just replaced my fuel filters on my 340 DA. ($$$) I have two(2) questions 1. I have seen the filters on the web for $ 20 a set, has any one used these?are they any good? if so, can you tell me what ones that you purchased? 2. Can I just install a remote spin on water separating filter to the...

I'm having issues with my port key pad. The pad is intermittent, and as such does not allow the engine hatch to be operative. I have been in touch with a company called Blink marine which sells the pads (kidney style) but you have to purchase both pads at a cost of $1500. Has anyone purchased...

Aculift is now called QMI group, they can be found on the web, they are still in buisiness. Call and leave a message thats how i reached them. They are in Canada with a location in the carolinas also.

I own a 06 340, the port kidney pad is malfunctioning so im going to jump the existing relay, and,install a switch to lift the hatch. After looking at the wiring diagram for this year boat i can't locate if there exists another relay (Other than the one shown in the wiring diagram.)that brings...

Ok i fiund it its called a y bid

Does anyone know the name of the screw bit used to removevthe bilge EIM screws.

I have an 06 340 Sea Ray, has anyone wired an auxillay switch to lift the engine hatch, if so can you describe how itvwas done.

A 320 MAY have 6.2's most have 350 MAGS, I owned one with the 350's to make that boat preform properly the props have to be changed to 18x18 DQX.( I did that and the outward response is significant.) The 340 will not have 6.2's most have 8.1's I would caution anyone purchasing a 340 with 6.2's

How did you wire that aux switch, I might have to do the same thing. I have been in touch with Digital Marine Services and Blink Marine. Digital Marine has a nicer looking pad with a 1 year warranted, Blink has a two year warranted, but not as nice looking. At any rate if I have to replace the...

To answer the question on profile, i own an 06 340 sea ray on Long Island NY, 350 hours white hull with 8.1s. I have power to the key pads however my port key pad is not allowing the engine hatch to open. I want tovsend power to the ECM in the bildge to see if it operates the rams, if it does i...

Married

Is there a way to jump wires under the helm sobthat i can kift my hatch?

Thanks, I will look for it. The 06 parts manual does not list it anywhere, and there is no part # for it. I have called several Marinemax dealerships, and there isn't anyone that knows where it is located. Also, I called Sea Ray and they stated that they no longer give tech support for any boat...

I need to replace two (2) rams on my 340 . I have found a replacement for the Acculift made by Thompson Linear Part # DM12-10A5-18SS. Does anyone know where the hatch relays are located, just in case I have to replace them?

Sea Ray part # 1766064. The actuator is making a crackling sound when lifting the hatch, I saw that Harden Marine has an actuator #620-922018, the same travel,buy slightly less closed value. Has anyone used these?, or are there any recommendations on units that can replace the SR units. SR lift...

Thanks Kevin