Search results

Can the muffler remain in place or does it have to be removed in order to change out a Gen 3 cool fuel module on the port motor. ALSO,does the exhaust manifold have to be removed. Any tips on this would be greatly appreciated.

Can you check the transmission fluid level when the transmission is cold?, Is dextron iii ATF the proper fluid to use/fill the transmission?

I just replaced my fuel filters on my 340 DA. ($$$) I have two(2) questions 1. I have seen the filters on the web for $ 20 a set, has any one used these?are they any good? if so, can you tell me what ones that you purchased? 2. Can I just install a remote spin on water separating filter to the...

I'm having issues with my port key pad. The pad is intermittent, and as such does not allow the engine hatch to be operative. I have been in touch with a company called Blink marine which sells the pads (kidney style) but you have to purchase both pads at a cost of $1500. Has anyone purchased...

I own a 06 340, the port kidney pad is malfunctioning so im going to jump the existing relay, and,install a switch to lift the hatch. After looking at the wiring diagram for this year boat i can't locate if there exists another relay (Other than the one shown in the wiring diagram.)that brings...

Does anyone know the name of the screw bit used to removevthe bilge EIM screws.

I have an 06 340 Sea Ray, has anyone wired an auxillay switch to lift the engine hatch, if so can you describe how itvwas done.

Is there a way to jump wires under the helm sobthat i can kift my hatch?

I need to replace two (2) rams on my 340 . I have found a replacement for the Acculift made by Thompson Linear Part # DM12-10A5-18SS. Does anyone know where the hatch relays are located, just in case I have to replace them?

Sea Ray part # 1766064. The actuator is making a crackling sound when lifting the hatch, I saw that Harden Marine has an actuator #620-922018, the same travel,buy slightly less closed value. Has anyone used these?, or are there any recommendations on units that can replace the SR units. SR lift...

I have an issue with one of the wire leads to the port battery switch. Sea Ray service has said that there is a solenoid in the maid DC panel located in the bilge of the boat on the wall that has a fuse on it. 1) Has anyone removed this cover, and if so how was it done? 2) Did you see a fuse in...

I am interested in a 2006 38 Sea Ray with the 8.1 HO engines. I spoke with my local Marine Max dealer and he informed me that the hard top fetcher slows the boat down 2-3 knots over the 04-05 380's. Has any owner of a 2006 380 feel that the performance in the mid range to upper range is...

I have a 04 320 with the factory microwave. It seems that this unit requires a lot of time to heat up items as compared to my house micro(not knowing the wattage of my house.) At any rate has anyone changed out their microwave on their 320, and if so what did you replace it with. Also how was it...

I am interested in installing a satelitte antenna on my 320. My concern is the location of the reciever. Has anyone installed a reciever into the cabnet of a 320, or where do you suggest that the reciever be placed. I dont want to alter the cabnets. 2004 320 DA w/t 350 mag mie

last season i did not spray my prop shafts and at the end of the season they were loaded with barnacles. I did however bottom paint my trim tabs and rudders and exhaust only to find that the trim tab bottoms were covered with barnacles, does the zink spray control the growth on the shafts, or am...

I'm in need of some information, I'm looking to move from a 3 blade 18x 19 prop to a 4 blade 18x17 prop for my 32 sea ray. I have seen the CJR, and teinbridge advertised on the web, however when nI cintacted Sea Ray at the plant they had no spec on which prop to purchase as they did not outfit...

Just got done with filling my 5.7 with anti freeze, I drained the mufflers,my question is do I have to put any antifreeze in the mufflers or can I leave them just drained. 2004 320 DA T 5.7 MIE

I live in the north east, and have used Shell Rotella straight 40 weight oil. As this is difficult to obtain, I was told by a Shell tech that I could use the Rotella 15-40 oil. My question is at what temp will the multi vis oil reach it's 40 weight. My engine runs at 158-159 all day, and takes...

Had trouble the other day with the vacu flush not flushing. I was told that there was issues with the 2004 Sea Ray vacu flush motor( No longer maid by Leeson.) Has anyone had experience in changing the motor out. Ther is little room at the back end of the vacuum generator to turn the coupling.

Has anyone had experience in removing the Back seat bolsters on a 320 DA. I located the screws of the rear seat back in the boot locker, however i have not located any rear screws for the back bolster near the helm seats and the companion seat on the port side. I have contacted Sea Ray and they...