Search results

Anyone know where the hydraulic assist pump is for the ray marine auto-pilot? Never noticed it...

Its actually below the tank in a small crawl space. I've done mine once before. For the other side remove the exhaust hose from the Gen (at least on the Onan.)

while back there I would do routine maintenance and repack the rudders... since you are there. Cummins here but pulling similar stuff out to change charger so while there!~

So just went down to the boat and flipped the charger switch and looked in the bidge and my trusty old PD2140V was smoking! She was a great unit until today so I am thinking of going with the same unit- Plug and play easy. Might kick it up to the 60AMP from the 40 but heard that the breaker for...

good call - It has vents above from the factory one. I also vented the fridge up and through when I installed the Vitirfrigo Fridge so it would not over heat and/or burn out.

Hey Everyone. I notice online (facebook) some one replaced their microwave. I looked at the model and found for a couple more bucks the convection model that is the same size GE MODEL JES1109RRSS. Anyone swapped this out? My black factory sharp lost its LED years ago but I can make it work the 3...

Got a question for you all. Going to change out the stereo. old oval piece in the cabinet has many cuts into it. gong to route a new piece of wood. but t has that white Formica on it and I need to replace that to make it look uniform. anyone know the color code Sea Ray Used??

Got the studs out at a machine shop. resurfaced the face. going to reinstall and replace many connecting parts -($400 overnighted from sbmar.com) and hopefully back in action this weekend. Thinking about having both fully gone through and new seals and sleeved this winter. anyone else done it...

I'm a lightweight- 165 so I have stepped on the bridge (seeing when they put my shrinkwrap up and seeing footprints there has let me to believe it can support it) of the window... BUT! my preferred way is though the bimini windows. note wear sneakers as to not slip and bring wax and a rag to...

ok guys got a new one. My exhaust elbow on my Cummins 6CTA if bolted in by 4 bolts. Looks like while under way yesterday in 4 footers they were rusty and 3 of them snapped off. I lost power which I don't understand because it was after the turbo- unless from all thee black smoke and soot? I need...

Yea, pulled out the entire couch assy and electric motor assy. only to realize it gave me about 1" more play. Couple wrenches thrown that time. When it comes to water pump on that side a check gets written.

Throwing it out there again. Anyone found a microwave that is plug and play size? No modifications? I don't mind them but if a new one fails in 3 years and need to replace again I don't want to be re-cutting AGAIN. Funny thing is I have not even used mine except for popcorn in 7 years. But the...

For NE I cannot stress the best of the best is H and H prop. would not use anyone else... https://www.hhprop.com/

Just curious- before you do all that have you checked your shaft bearings? I mean most of the time if the props look good and the shaft bearing is loose... you know?

I like the Push - pull method for the blowers as it is more smooth in circulating the air. I also like to leave my blowers running for about 10 minutes after I power down the engines. I find it 1 cools off the engine room by a couple degrees and in turn helps with cabin temp (even if by a little)

I was told by the factory I was one of 6 to 8 built in 04. One is for sale in South Portland ME currently. Sorry for the delayed response. I am not getting e-mails from CSR when there is activity.

I think my dad installed those on a 88 wellcraft San Tropez in 1990 and they haven't changed since! LOL

ok. So I have failing tach's. one went bonkers like 2 years ago. last run of the seasonlast year the other one started to bounce. question is what have others done? I like the OEM look and the hour meter, but am open to better options/ suggestions. I have one option of Flonder pounder/...

I have a garmin 7612XSV but the 8612 would be the same size. Once you pick it, send the specs of the chart plotter to flounder pounder when ordering the wood inlay. they will cut it to perfect size for the unit. easy peasy! (trust me pay them to do it. Worth every penny.)

I honestly do not recall. I did however stop by a local Ace Hardware and hit the 316 stainless section and bought the hardware and washers and everything for like 10 bucks. While I agree maybe due to different thicknesses? I also used screw heads for the bottom VS bolts for hydrodynamic reasons...