Search results

Thank you and yes, I plan on changing the fluid as well.

Hi Everyone, I am preparing to replace my transmission coolers. Seems to be a fairly easy job, but i have a question about the diamond step on the port engine. Any issues with removing the nuts holding it to the transmission ? I won't break a seal? Thanks in advance!

Hi Randy, I had the same issue a few weeks ago on my port side engine. Engine completely died and port side gauges were frozen (i.e. tach was stuck at 3000, etc, etc) I reached out to Mercruiser and they suggested i check all the ground connections They also recommended I replace the old...

Hi Willy G, I recently installed the Vessel View Mobile kit for this very reason. Once installed to the SmartCraft Junction Box under the helm dash, you use an application on your phone and connect via Bluetooth. If you do get an alarm, you will get a human readable message that clearly...

Kohler 359771 Oil Filter for 4EF, 5E, 6EF, 7.3E Generators : (partsfortechs.com)

Hi, From the screen, it looks like the STBD engine has high water pressure at idle. 43.5 psi Faulty sensor perhaps? if you throttle up, does the pressure on the stbd engine change ? port engine at 2.5 looks normal idling @ 650 The alarm mentions fuel level so that is confusing

Hi Outobie, check this out...Maybe one of these is a good substitute Marine Reading Lights (drsa.com)

Hi Outobie, I believe this is the searay part number, 1831205 I would try calling MarineMax parts dept to see if they still carry the part or if they have an equivalent

Hi Everyone, Need advice & feedback I was running the boat yesterday. I was out for a few hours a various RPM's. i was almost home and got the boat up to 3100-3200 RPM's. after about 5-10 mins at that RPM, the port engine shutdown. i mean completely off. gauges stuck at their last position. i...

Hi Everyone, Need advice & feedback I was running the boat yesterday. I was out for a few hours a various RPM's. i was almost home and got the boat up to 3100-3200 RPM's. after about 5-10 mins at that RPM, the port engine shutdown. i mean completely off. gauges stuck at their last position...

I ended up installing VesselViewMobile It gives you the smart craft alerts in human readable form. Very easy to figure out alerts, etc ,etc.

ICA valve ? Did you mean, IAC valve ?

Hi Everyone, New topic... Best way to check the Heat Exchanger, Trans oil cooler and oil cooler to see if they need to be replaced ? i.e. For heat exchanger, is it simply pulling the end caps and checking ?

ok. i am not going to mess with something that only requires a simple toggle switch. i am starting to have an issue with my DSM300 module to my C80. it intermittently stops sending to the C80 and when i unplug and plug in the power, the data feed restarts. I was thinking of using an unused...

Thank you !

HI, Thanks to everyone. This is unfortunately disappointing. The true intent was to remove the panel to gain access to unused switches. Ok, so this brings up a new discussion. on the panel i want to remove is the ACC1 switch. this is unused. how/where can i find where this terminates so i...

Hello, I am hoping someone can help. I have a switch panel i would like to remove, but i do not see any visible way of removing it. Here is an example of the panel i am referring to... Please ignore the circled switch. this pic is just for reference. Thanks in advance for your help.

Great Information ! I will check things out when i get down to the boat, but what you are saying makes a lot of sense. Thank you for the help!

Hi Fly4Kix, Thanks for the great info. I will check things out tonight. the SC to NMES2000 gateway, do you have a part #? where did you buy it ? I would love to create this gateway. the past owner had out in a Garmin Chartplotter and Radar, and while the Garmin can display sonar data, it...

Thanks ! I will check it out tonight. One thing that i am curious about is.... Last week i was out and the DSM module stopped feeding the C80. (turned out to be the power cable) However, when that happened, i was able to use one of the Smartcraft gauges to show me the depth So, it would be...