Search results

Looking for the STBD Side Cabinet above the dinette of a 95-98? 330 Dancer.

Hey Guys, A friend at the marina just purchased a 99 Regal 32 with a Kohler 6.5 Genset. Engine Starts/Stalls. Gen has 200 or so hours on it. I'm assuming it's either the temp switch or the oil pressure switch. Any thoughts would be greatly appreciated. I have had a heck of a time finding any...

Hey guys it's been a while. I'm heading to the lake to work on a 94 300DA tomorow night. Boat has twin 5.7 with v-drives. Last weekend the owner had a problem that within 5-10 seconds of starting the port motor the Alarm would sound. Oil pressure good, temp good, any other ideas of where I...

Just Trying to find if anyone knows the correct prop and size for a 1990 270 DA , with a 7.4L Bravo1. I checked sea rays prop chart but they dont list this particular boat. Thanx Dan

I have an 86 300 and the sliding cabin windows are getting to where they need new weatherseals. I would like to find a link with the replacement procedure. Also I would like to know the best place to order what I need. Lastly I need the screw cover trim for the cockpit windshield. Any help is...

I tried posting this question in a different forum to no Avail. so now I will try this one!! I am looking for an exact replacement Ignition Circuit breaker. My boats an 86 300. The circuit breaker is a switch type mounted right above the ignition switch. Thanks for any help. Dan

I have an '86 300WE with twin 5.7 I/B's. I am wondering if anyone knows what amp circuit breaker is used for the ignition. They are a manual switch circuit breaker mounted above the ignition switch. Also where can these be purchased. I would like an exact replacement. Thanx Dan

I have a 1986 300 WE. The boat is pretty much in completely restored condition minus a couple odds and ends. The one in particular that I wanna handle this off season is replacing the side cabin window tracks. Has anyone here done this and what is the procedure and best place to find the parts...

Anyone have the proper way to set timing on an '86 300 with 260 IB's. should i use the pointer below rubber plug in bell housing or timing marks on cover? stbd motor reverse rotation. I dont believe my thunderbolt has the purple wire to ground so how do you put into base time mode?

I will start buy saying that I am 33 years old and have owned 3 SeaRays so far, Currently an impecably mint 1986 300 WE with twin 260hp IB's. My wife and i have been kind of looking to go larger and probably convertable style. A local broker has a 1988 Luhrs 34 convertable that is very nice and...

I have a mid ninetys Onan 4.5kw Genset aboard my 1986 300WE. didnt come with the service books and wonderin what viscosity oil to change with ? synthetic ok ?

I have an 86 300 WE with vacuflush head. The pump continuously runs and will not shut off. If it runs for 20 seconds or so it makes enough pressure to flush. Last week I climbed to the stern of the boat( TERRIBLE JOB) and replaced the duckbill valves. The problem is that I should have read the...

First off I will start by saying I Have owned my 86 300we for 6 years now and have never had any vacuflush issues. This year after dewinterizing i noticed that now the vacuum pumpruns continuously as if a pressure switch isnt working. Hopefully someone out there has run into this. Thanx Dan

This might be the dumbest question i have ever asked, but i am gonna ask any way!! I have RayMarine 220 series VHF aboard my ray 300. My mic. holder broke upon my boy thinking that you need to slam it in place rather than set in place.(he's 4) I went on there web-site and it said to get it from...

Does anyone out there have the proper timing procedure for a 1999 model year crusader 7.4L MEFI engine?? Pretty sure it wants to be at 8 degrees btdc, but unsure of how to put it into base timing mode. Thanx Dan

Hey Guys its me and once again lookin for some help!! Workin on a different brand boat (Baja). Need to find engine management schematic like ASAP. searched all over online with no luck! Boat is 2000 model year with a 7.4L Merc.MPI Bravo1 drive. If any of you know where I might be able to...

I have a 1986 300WE with twin 350ci merc IB's. Since I have had the boat( going on 5 years) the port motor has been lacking power compared to the starboard side. Recently it has gotten to the point where the port side will only turn around 3k,feels very flat, and has a noticeable upper end tick...

Does anyone know of any place that specializes in older used parts?? Looking for a contact for a place that salvages and sells the hard to find exterior parts for mid to late 80's cruisers. Thanx Dan

Hey , Question 2 ya all. My dock partner has a 1988 Sundancer with twin 5.7 Litre Alphas. During winterization last year he noticed the nuts on the inside transom area of the gimble housing assembly to be rotted off. The boat was a prior salt-water boat but now in Fresh water. Question is does...

I have a 1986 300 WE. The limber holes in the stringers have sections of pvc pipe inserted in them. I read that these should be removed and the holes fiberglassed before rotting of the stringers occurs. My stringers are still perfect but I want to make sure they stay that way. Wondering if any...