I believe there will be a small brass plate riveted to the top of the drive near the linkage.
My guess is it will be a 72C if you have 7.4 big blocks. If I am correct it is 72C. Additional numbers
would indicate either reverse or normal rotation.
Just a thought. I am in saltwater and have gotten my fill doing valve jobs due to the two problems with saltwater taking out valves and once an engine. So I converted to 496 dry joint manifolds and slightly changed the geometry of the elbow down angle. And as long as I was at it I moved my...
Keep in mind that the manifold bolt is angled down towards the bolt head due to the sloping side of the head. This allows a short swing angle for the mallet under the other engine manifold. Do an outside manifold bolt first. Once you get the idea that works you can then tackle the between the...
1988 340 dancer, been there and done that. Picked up a set of "metrinch" sockets. Picked the socket
that was just a little too small. Using a ratchet extension, the socket and a 2 lb mallet I just beat the socket
on. Got all the rusted bolts out of all 4 manifolds. by the time I was done the...
From an electrical engineer and commercial construction contractor, (yes I also own a sea ray). Low voltage during loads is usually caused by 1. overloading (by other boats in the marina) 2. Problems in balancing or connections in the marina 3. Utility overloading (brown outs). I would...
Not going to say normal but certainly well known issue. Google Rochester Leakdown. Most if not all passages in the carb are drilled out. The access hole for the drill bit is then plugged with a "well plug". This tend to leak with age. There is a fix procedure. I also had other issues so I...
Sure is lots of misinformation out there. I will not add to it, I do NOT know what a rolled exhaust cooling system is. I do know that the 7.4 manifolds are not available with the configuration for
dry stack. The 496 manifolds, contrary to popular belief, do fit the 454. It does require
a...
Your info does not say if it is a Dancer or Express. I do not know what an express bilge looks like
but your pictures are very similar to my 1988 340 sundancer. The exhaust hose runs are short so
the two ends must be close to lining up. If they do not, moving the muffler might make it work...
Just a thought about changing the fluid copied from a non boating website
No, it is not as hygroscopic as brake fluid. However, it can degrade over time - especially if the level is low and it gets overheated,
Lots of trips to catalina, south to Dana, Oceanside, san Diego and even stayed in Ensenada for a couple of years. Rarely short trips north. Twice to Long Beach for a day.
This weekend the first mate and I are guest slipping in alamitos bay for two nights. Any suggestions for must see/do in...
Oh my gosh, 5 responses and all are mostly likely thinking aluminum with some caveats. Thank you all. I know they are original so al. it is. At unlike most things this is the answer I was hoping for. Thanks all.
I am about ready to install a new autopilot. I am considering changing the current location of compass sender from under the head sink to a little nook under the aft berth. Install instructions say to keep it away from metal that could cause a false reading. Makes sense. This planned location...
I have a 3 burner cooktop that gets close to 3 kw, a water heater that I suspect is close to 1 kW
(can't remember, maybe only .75), then an icemaker, refrigerator (both intermitent loads).
Microwave, maybe another 1 Kw. Never clamped the load but I can trip the 30 amp breaker. A 30 amp...
My 88 340 da came from factory with a 6.5 westerbeke. I load it up with the cooktop. Even unloaded i have never had fouled plugs after 28 years of ownership
Good point about twisting the membrane, I used needle nose pliers with little pressure on the threads so it could be adjusted while in place. don't squeeze to hard and ding up the threads.
they manual says it is calibrated at the factory, do not adjust. why would it say this if there was no way to adjust. the switch has a knurled thumb wheel against the spring. turn it compress the spring and cutoff pressure goes up. turn it to decompress spring and vac pressure goes down. set...
I googled it for my on use and found 10 inches HG. I recently upgraded/replaced ducks, some hose, upper/lower pump body, upgraded bellows and motor. My switch went south about ten years ago during a trip, bought a wheelbarrow inner tube at the island hardware and made a new diaphragm. not...
Over the years I think the aging of throttle cables are sneaking up on me. To the point that
I find myself tapping the throttle lever to make small changes to RPM as just pushing doesn't do anything at first then a big jump. I suspect the cable sheath is just flexing at first and then suddenly...
I have had 2 series 6 volt golf cart batteries for the house for many years but always a little short after 2-3 days. Misc loads including refrig on inverter. I would like to increase capacity. I have a 80 amp alternator on my genset and 90 amp alternators on my mains so charging when engines...