Search results

It's 13' nominal. I'd have to measure to get the exact width. The well is also 35' in length and the marina won't allow you to stick out more than 4'. So, this means a 39'x12.5' boat would be about the maximum. My neighbor has a 360 Sundancer that has these exact dimensions and he's pretty...

Thanks for the good information on the moister issues. I would definitely have the boat surveyed. My budget falls right in between what the 1999-2002 and 2003-2008 are going for now. My first choice would be the 2003-2008. I definitely like the more modern styling and the extra beam. I would...

Hello, I'm shopping for a 340 Sundancer. I'm interested in both the 1999-2002 and the 2003-2008 versions. Are there any areas of concern or things to look out for on either of these models? I definitely want V-drives and either 7.4L or 8.1L engines. The 6.2L seems like it would be a bit...

That is probably what I need. Thanks!

The photo I attached is not of my boat. It's just a photo I found on this site with the same plumbing. The leak I have is just a slow drip at one of the compression fittings. Tightening didn't fix it. I wanted to replace the fitting. Mine do not look like the picture you attached. The fittings...

Here's a picture of what mine looks like. The plastic hose has 5/8 written on it.

I have a 1990 310 Sundancer. The freshwater system is plumbed with a grey colored 5/8 polyethylene hose. The elbows and tee fittings are a grey plastic with compression fittings. The compression fittings have a brass nut. Any idea who makes these fittings and where I can find them? I have small...

Well, I tried the Marine Part Depot cap and it didn't fit either. It's the same thread size as all the others I've tried. Anyone else have any suggestions? The cap I need is the same diameter as all the replacements I've tried. It just appears to be a finer thread size. I hate to replace the...

Thanks! I ordered one of these and will give it a try. I talked to the Sea Ray dealer again and they said the supplier that made these went out of business and the replacement caps are no longer available. They said this supplier used a different thread size than most others.

Try this... http://www.marinepartsplus.com/catalog/mercruiser/serial/5.0L_EFI_GM_305_V-8_1999-2001/809500+99

Does anyone know the right part number or where I can find a replacement water fill cap for a 1990 310 Sundancer? I looked it up in the parts manual and it said part# 522557. I bought one of these from my local Sea Ray dealer but it doesn't fit. It appears to be the wrong thread size.

I'm looking to have many old coats of bottom paint stripped off and then the bottom repainted this year. Can anyone recommend a good contractor for this in the southeast Michigan area?

Is there any difference between the regular Spray Nine and the "Marine" Spray Nine other than cost?

Thanks for the reply, Frank!

I was going to install an in-hull transducer, but after reading the instructions, it says that it can't be used with cored hulls. Does anyone know if my hull is cored? The boat is a 1990 310 Sundancer. Thanks.

I have a 1990 310 Sundancer that has water stains in the cabin headliner. The boat had some water leaks in the past that were repaired by the previous owner. I understand this was a common problem on these older Sea Rays. The boat is in perfect condition other than these stains and it kind of...

I buy the filters from here. $43.95 http://bpi.ebasicpower.com/pc/ALTFK316940/ALLHURTHPARTS

Anyone use Aquagard bottom paint in freshwater? Just wondering how well it worked. The price is less than other paints and the water base would be a bonus. I've been using Pettit Vivid for a while and have had good luck, but it's a bit pricey.

You probably need to replace the neutral safety switch on the transmission.

Thanks. I was looking at Amsoil or Royal Purple as a replacement.