Search results

Just put my batteries and plugged the old girl in today. I have no AC lights though. All the other AC accessories seem to work except for the cabin lights, any thoughts?

The crimp fitting on my sink spray handle came off last weekend, does anyone have a part number for the hose and / or handle assy? I believe it's Italian because the fitting threads are different, some non-standard metric size. Thanks

I am trying to replace the AC light bulb over my galley. What's the trick to remove the cover without breaking anything? See Picture attached

I am trying to test my emergency bilge pump, but I can't seem to disable primary pump from coming on. I have tried shutting off breaker in electrical panel and shutting off both electrical main switches. The main pump still keeps coming on. Does anyone have a wiring diagram? Thanks

My 99 310 Sundancer seems like the ac temp was acting strangely at the end of the season. When I hit the "temp" button for inside air temp, it shows double dashes (--), not a temp. Has any one else experienced this?

Has anyone been able to find a replacement or something to repair a curved lower locker sliding door On a 98 to 2002 310 Sundancer? I had to force mine open and I broke some of the slats. I was wondering if somebody had come up with a better idea than this.

Does anyone know where I can download this info? Wondering which battery powers up the bilge pumps. 2 starboard wired in series, or single battery for port engine?

I was wondering if anyone has ever put there Bimini sections, not with eisenglass or screen, Into the washing machine on a light cycle. I would like to do my Bimini boots and the rear Bimini cover. Also I have some filler sections between the windshield and the front Bimini with nothing but...

My 1999 350 mag runs runs very rich, especially on startup. I had the spark plugs out today while changing the exhaust manifold's and all the plugs were black with carbon. When I start it cold, it smokes and you could smell the fuel. Seems to get better when warming up. Any ideas what could...

'99 Sundancer with 300 mag 350's and V-drives. I have this "chirping" type noise coming from the exhaust. You can hear it inside the engine compartment as well as from the exhaust ports on the starboard engine. This started late last year. I noticed it when first starting the boat. The noise...

'99 Sundancer with 300 mag 350's and V-drives. I have this "chirping" type noise coming from the exhaust. You can hear it inside the engine compartment as well as from the exhaust ports on the starboard engine. This started late last year. I noticed it when first starting the boat. The noise...

Does anyone have a supplier or part number for the black rubber seals on the engine area floor plates? I believe they're thick black rubber. Not sure if originally glued down or self-adhesive?

My 99 310 dancer with 350 mags and V-drives has a "ticking" type noise heard from the dock coming from the starboard side exhaust discharge until the cooling water starts to flow. It is not a leaking exhaust manifold gasket, definitely seems to be coming "through" the exhaust tubes / pipes. Has...

My '99 310 dancer started exhibiting a "ticking" noise from the starboard engine (350 mag)after being started. This noise appeared to dissipate when the cooling water would start flowing out the above water line exhaust ports. (As Heard from the dock) While having the engine covers opened during...

I have a 99 310 Sundancer with 5.7 mags. The Port V Drive blows trans fluid out the vent at times under hard acceleration, I assume that this is when I am getting up on plane as I cannot watch when it actually leaks.. I have checked the fluid level over and over. I have also swapped the trans...

99 310 d a 4.5 westerbeke genset. Last week it worked fine with the start and preheat buttons. This week, when I engaged the on-off switch the led doesn't come on in the switch or it makes no attempt to crank. I've looked for Breakers that might be popped but I don't see any. Does anyone have...

My 99 310 d a doesn't seem like the vacuum flush wants to refill with water like it did last year. Any ideas? If I hold the pedal up it will slowly fill.

Does anyone know the part number or where I can find the windshield screw cover trim on a 99 310 dancer? I can't find it in the parts manual and Flounder pounder has some trim but I'm not sure it will fit.

Does anyone know how to get new packing for a '99 310 DA? It looks like a solid piece, doesn't appear to have the "rings". Also any tricks to adjusting it? Stbd. side extremely tight fit with generator, etc. in the way of the adjusting nut.

'99 310 Dancer w/ vdrives. Last year I noticed at my port side steering support base, that there are 2 visible vertical cracks in the epoxy coating that have brownish stains and water seepage coming through. The water is then puddling up in the "trough" at it's base. Has anyone ever seen this on...