Search results

Measure how much you need and let me know if this will work. https://clubsearay.com/index.php?threads/swim-platform-parts-accessories.113448/#post-1452060

Interesting video here shows apparent losses of power onboard and clear change of direction. Just a horrible situation all the way around.

My St Paddy's shirt should be here tomorrow....

This should be someone's winter project list: Replace Worn Out Swim Platform Trim & Vent Inserts

In addition to replacing the existing e26 bulbs with LED's: (https://www.amazon.com/gp/product/B07MCGH7N4/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1) I added 6-8 of these throughout the engine room. https://www.amazon.com/gp/product/B08GG18HVW/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1...

https://clubsearay.com/index.php?threads/270sd-ob-conversion.111795/

Ladder is SOLD.

That's a good location and you shouldn't have any problems with current & wakes, especially since I'm assuming you'll be inside of other boats. Pirates Cove at WRYH and Stan & Joes Riverside next door are popular spots. The Flat Island area in the Rhode is a great anchorage. We also used to...

We're off the Rhode River so we're on the West all the time. Where are you looking? The West is very convenient to all things mid-bay, including Eastern Shore destinations. Where you boat and what you do impact the location more than the opposite. More info on what you do, where you want to...

Have various parts/accessories that were removed from a 290AJ platform: Windline TPL-3X 3 Step Telescoping Pocket Ladder, was on boat less than 14mo. and only deployed a few times, includes sliding mount hardware Oval Vent Inserts w/SR Logos Oval Vent Inserts w/Swimplatforms.com Approximately...

Eliminate the easy stuff first. Had a drive fluid leak before and it ended up being the reservoir cap. There is a vent built into the cap that failed and allowed fluid to leak throughout the bilge. Literally a $5 fix.

Eliminate the easy stuff first. Had a drive fluid leak before and it ended up being the reservoir cap. There is a vent built into the cap that failed and allowed fluid to leak throughout the bilge. Literally a $5 fix.

Where are you receiving the temp error? Is that a SmartCraft error or on your MFD? I don't believe the 2 communicate so my guess is a sensor on the fresh water side of the engine is throwing the SC error. As for the transducers, remove the plug from the ring and unscrew the transducer...

I don’t think the HW heater needs to be on for the pressure relief to release water. Once the water pump is turned on, the entire water system, cold and hot, is pressurized. A new relief valve is a cheap initial fix but could also just be a bandaid depending on the age of the heater. There’s...

Larger one is cockpit sink/livewell drain and the smaller one is the pressure relief drain for hot water heater.

There should be 2 knobs, on the outboard side of the seat, that keep it from sliding.

Dripper Guards seem to work well as long as they are not close to waterline. Tried them on my AC discharges, close to waterline, and lost them one by one. They actually sent me a few replacements but they came off as well. Went back with small tubing sections siliconed in and haven't had a...

I had contacted both when I redid my dash but chose Tecnographics for the reasons Brad mentioned (finished rounded edges, glossy finish, etc). The price wasn’t that much higher and they did have the template for the 290/340s at that time, including trim tabs, drive trims, spotlight. I did a...

I did the same project on my 290. I used all Attwood stainless thru-hulls, I believe I got them all from Wholesale Marine. Felt like it made a nice upgrade..