Search results

It looks like I'm going to need to replace my thru-hull depth/temp transducer. Just wondering if anyone has experience and if there are any special instructions (i.e. procedure, tools, lube for seals/o-rings.etc.). Thanks for any input!

I have an issue with my Smartcraft Tachometer readings. I'm not getting any info for depth or sea temp. I know they use the same transducer and I've unpluggged and re-plugged the connector hoping it was just corrosion on the plug. One interesting thing, when you first turn on the ignition the...

I was doing my annual winterization this past weekend and had a strange occurance. As I began to pour from a new (still sealed) gallon of Mercruiser Synthetic Blend 25W-40 the oil was coming out sort of "gloppy" and appeared to be separated. After shaking the bottle vigorously to mix it seemed...

Anybody have this problem? I altered our lube bottle cap (so as to not over-pressurize the bottle) to allow it to be fully vented (removed the one way rubber valve), closed that hole and left the very small (about 1/16") dia. hole in the cap open to act as a vent. Even with the lube about...

Has anyone had issues with the Mercury sealing washers not working properly. Strange that mine showed no leaking during the winter but last week (on the lift) I noticed a streak of oil running down the skeg from the screw. Checked tightness and it was tight. Do any of you us a set of vice...

Dave: Yesterday we exchanged a few comments regarding upgrading your chartplotter from the Navman 5500 to the (as they are now called) the Northstar 550. I wanted to know a few things about that if you don't mind: 1. Did you have to drill any new holes or did it just drop in? 2. Did your...

I'm in the process of replacing the port and starboard bilge area vent covers (they are about 54" long) on our Sundancer. SeaRay provided me the new covers (at reduced cost) but the install is my responsibility. I believe the failure is due to the use of an adhesive that is far to rigid and...

Anyone had any experience with the Sears Platinum AGM battery. I'm considering replacing the batts (2) and I'm looking at the Group 31 in particular. I have one of their AGM's in my Tahoe and it's been great but I'd like to hear if anyone has marine experience with these. Thanks!:smt001

Since someone asked me to start this thread in the "generator" thread; here goes. First, what are we talking about when we say "bypassing the water heater"? I assume you mean installing a bypass hose so you can winterize without having to fill the heater with propylene glycol. For the record...

Since we all had so much fun with Honda generators I thought I'd try this one. Here in LA (Lower Alabama) we always have an issue with Muddaubers building nests in the craziest places on our boat: thru-hulls, speakers, and the worst, in the bimini top (folded with the boot around it)!!:smt013...

Anyone have experience with these. I've been considering installing the A6 model on our boat but not crazy about drilling holes under the waterline. I have considered mounting them on the underside of the swim platform but not sure how effective the lighting would be with that arrangement...

I would like your thoughts/experience on using a Honda generator. I'm considering buying the 2000i model and using it occasionally for a/c at night. I lnow all of the CO issues and we have 2 CO detectors in the cabin. I was considering locating it on the swim platform (secured very well, of...

Has anyone had experience with vertical hairline cracks forming in the plastic deck vent covers that cover the vent screens for the engine area. These vent covers (about 40" long) are on the outside of the hull and run fore & aft. They are held in place by a sealant similar to 3M5200. The cracks...

Hello to all members. We currently own a 2006 240DA w/350 MAG Horizon Bravo III. We bought our first Sea Ray back in 1984 (it was a 1974 SRV 200) -- we had a lot of fun with that boat! Anyway, glad to be here!