vessel view

Good morning SeaRayGang. 2011 SR 260 Sundeck here with Merc 5.0. In two different instances, Engine Guardian engaged on my boat without announcing any specific system faults. See below for more context. Long and short, engine guardian is engaging but nothing is getting annunciated on Vessel...

Vessel View 4 brand new in the box. Never installed $1000. Email me at goboater909@gmail.com

All, I am in the process of creating a NEAMA2000 network for my Garmin Chart plotters to receive data from Smartcraft to VV. However, can this same network be the GPS for the VesselView? My GPS is not currently working and I do not have the Skyhook feature etc. I just bought the boat this...

My SmartCraft 5000 is having issues so Mercury Marine tells me it is possible to upgrade to VesselView 403 or others. I want to do this myself and want tips from others who have done this. Following is my understanding of this job: 1. Determine if behind my helm there is a J-box with 2 open...

My display on a 340 2007 Sundancer is very weathered and hard to read. Can the plastic be replaced or do I need to upgrade to Vessel View? I am actually looking at purchasing this boat with this Smart Craft in this condition what are my options? Day number one on this site, my current boat is...

We have 2010 DA370 with AXIUS. Recently noted Vessel View intermittently indicating a starboard engine trim tab and/or crankshaft sensor warning when up on step, oscillating between OK and the sensor warning. At about the same time the starboard electrical circuit started to malfunction...

Hello, I just finished sea trial on a 2004 320 sundancer. I found out during the sea trial the" Vessel view" is not working. Is this a module that is one part of the whole system? I spoke with the local Sea Ray dealer and they told me it could cost up to $2200 to replace. Has anyone had this...

After installing Vessel View Mobile, I show a Level Sensor Tank B Fault that popped up. The Port Fuel guage on Smart Craft guage shows fuel level movement when I gas up. I'm seeking any info/help on where it is located, what it looks like and advice on addressing this sensor fault? Boat is a...

Hello Crew, I just purchased a 2014 Sea Ray Sundancer and will have it next week (can't wait :D). My current boat is a Chaparral 290 Signature with Garmin Chartplotter and Auto Pilot and I am enjoying all the features like Auto Guidance and automatic Auto Pilot engaging from my Garmin setup...

Not sure how much popularity I will get here but I am able to repair most all LCD displays. From Garmin chartplotters to Yamaha smart gauges. I have recently tried my luck with 3 separate vessel view displays and was successful in bringing it back to life. Message me or email at...

I recently replaced my SC 5000 with a VesselView 502 on my 2006 44SD with twin 8.1's. The only way to power up the VesselView is to have both engines ignition turned on, engines don't have to be running. I have a friend that has a 40SD and his gauges and SmartCraft/VesselView 7 are wired to...

I pulled out my 2008 310SD From water for maintenance for couple weeks but my vessel view suddenly losing its brightness and became very dark and hard to see during the water test. Anyone got the same situation? Anything I can do to fix it by myself?

Mercruiser Vessel View - Smart Craft - Model Yr 2009 :smt021 - now since the boat has been new I have had consistent problems with Mercruiser, Hardware, Software, and technical assistance. - Hardware: Relies on old Technology and Communications protocol's. It only adhere's to the Old NEMA 0183...

We Have a 330 DA (Sundancer w/ Axius, Bennett Tabs, and Vessel View (Mercury)) How would I integrate the existing trim tabas (which do not have any indicator installed that I am aware of) into the Mercury Vessel view (which appears to be able to show the tabs as it has a calibration settings...