BeebopInPB
New Member
- May 22, 2022
- 12
- Boat Info
- 2011 sea ray sundeck 260
- Engines
- Merc 350 bravo 3 outdrive
Good morning SeaRayGang.
2011 SR 260 Sundeck here with Merc 5.0. In two different instances, Engine Guardian engaged on my boat without announcing any specific system faults. See below for more context. Long and short, engine guardian is engaging but nothing is getting annunciated on Vessel View (VV is properly connected; I'm getting telemetric data for RPM, fuel, temp etc). My apologies if this is a dupe thread, I did not find any threads addressing my issue.
Specific Questions I have:
1) Are there situations where a fault code could appear, but not display on Vessel View? (if so, wtf?)
2) Where would be the first place one would look to try and diagnose this issue?
This issue actually occurred to me twice – first time on the Maumee River, second time in the Lake Erie headed from Catawba to PIB. In both cases, the boat will run just great for about 20-30 minutes. Both occurrences, the boat needed to be running at about 3000-3500 RPM for about the 20-30 minutes for this to trigger. Once it triggers, you hear a single one-second beep and the engine revs down to idle. In both cases, I took it out of gear, assessed on the smartcraft gauge and didn’t see any warnings (like I did with the temp plug last year). I put the boat in gear again and got on plane again, and in both cases, it occurred again. On the second occurrence out in the lake, it occurred about halfway to PIB from the Catawba park ramp. We turned around and headed back at about 3000-3500 RPMs and it only triggered a second time.
Between the first and second time on the boat, I ordered and installed a Vessel View Mobile module (it’s connected to the CANbus connection behind the helm; it’s actually connected and just laying on the floor inside the access panel in the berth behind the helm). The only code that occurred did not show up the first time the Engine Guardian occurred; the second time it occurred, the SmartCraft gauge indicated a ‘SYS FAULT’, and the code 2011-23 appeared on vessel view (which is just a code indicating that there was a system fault). No further faults were recorded by Vessel View.
2011 SR 260 Sundeck here with Merc 5.0. In two different instances, Engine Guardian engaged on my boat without announcing any specific system faults. See below for more context. Long and short, engine guardian is engaging but nothing is getting annunciated on Vessel View (VV is properly connected; I'm getting telemetric data for RPM, fuel, temp etc). My apologies if this is a dupe thread, I did not find any threads addressing my issue.
Specific Questions I have:
1) Are there situations where a fault code could appear, but not display on Vessel View? (if so, wtf?)
2) Where would be the first place one would look to try and diagnose this issue?
This issue actually occurred to me twice – first time on the Maumee River, second time in the Lake Erie headed from Catawba to PIB. In both cases, the boat will run just great for about 20-30 minutes. Both occurrences, the boat needed to be running at about 3000-3500 RPM for about the 20-30 minutes for this to trigger. Once it triggers, you hear a single one-second beep and the engine revs down to idle. In both cases, I took it out of gear, assessed on the smartcraft gauge and didn’t see any warnings (like I did with the temp plug last year). I put the boat in gear again and got on plane again, and in both cases, it occurred again. On the second occurrence out in the lake, it occurred about halfway to PIB from the Catawba park ramp. We turned around and headed back at about 3000-3500 RPMs and it only triggered a second time.
Between the first and second time on the boat, I ordered and installed a Vessel View Mobile module (it’s connected to the CANbus connection behind the helm; it’s actually connected and just laying on the floor inside the access panel in the berth behind the helm). The only code that occurred did not show up the first time the Engine Guardian occurred; the second time it occurred, the SmartCraft gauge indicated a ‘SYS FAULT’, and the code 2011-23 appeared on vessel view (which is just a code indicating that there was a system fault). No further faults were recorded by Vessel View.