Search results

Got old one out. Need to get new norcold in. Please share your experience doing this. This is a 410DA. thanks, Jon

OK I’m putting Fox gateways on my engines which I successfully did, I pulled all the analog gauges and I taped off all the wiring for the gauges and secured it. I went ahead and installed the gateways and I go to start the engines it they just crank, no fire, both engines port and starboard...

Thinking about FOX gateways. Opinions? Experience? Thanks, Jon

have the 7608xsv and want to install a transducer. boat is in the water and not coming out anytime soon so a in hull surface mount is the key. Looks like there is a couple units available with a pot that seals to the hull surface and fills with liquid. Lake boat. Recommendations? Install...

Anyone have any crossover info on output shaft seal on a velvet drive 5000 trans... 1000-044-066 Thanks

I had reusable air filters on my 400 but they have given up the fight. They have aluminum frames and a black, synthetic filter media that is washable. Where can I find these? Thanks, Jon

400 EC with 7.4 MPI. Turn ignitions on and push start switch on dash, Nothing, no crank, nothing. Push and release start switch multiple times, nothing, then suddenly with another push it starts and runs fine. Replaced starter solenoid in brain box...still nothing, acting the same way. Any...

I know the shaft is 1.5 inches.... is the OD 2 or 2-3/8? Thanks, Jon

looking for torque specs for the tailshaft flange nut? Have been told 50 to a high of 200 ft pounds. Thanks, Jon

can I pull the transmission while boat is in the water? Sea Ray 400 express, 7.4 mpi. Jon

where does one find replacement parts for the B&G series speed/water temp transducers? Looking for B&G 200-00-128 replacement parts kit for a 96 400 Express Cruiser. Thanks, Jon

i have the factory converter in the boat and when in port on shoreline, I always keep it on. A friend advised that that is a no,no and will ruin my batteries? I am confused as I thought that the converter was for utilization of the 12 volt items on my boat when in pot\rt on shore power...

have a 400 express cruiser and the windshield has a filler strip, rubber foam, that fits in the frame that covers the attachment screws. Where can I get this rubber foam strip material? Its shrinking and a bit rotten. jon

Is flounder pounder the best place to purchase? Need momentary DPDT for windshield vent. It only closes will not open. I checked actuator and it works fine, so it must be the switch.... Jon

My 400, a 96 model, has a white flexible hose used to plumb the fresh water distribution on the boat. What is the material called? Can it be obtained from a RV supplier? I want to add a water line for an ice maker. Thanks, Jon

anyone recovered couch and mid cabin? Would v to see sme photos and find out how much material neede and any other info you might be willing to share. JON

Have just acquired a Garmin 7608 and wondered if there is an output on my 7.4 MPIs to hook up to? The GPS unit is Network Capable. Thanks, Jon

Need opinions. I am told 4 blade props are better for idle maneuvers and top speed? Is there an advantage? Also when going to 4 blade, how or does the diameter and pitch change? Thanks, Jon 400 Express Cruiser

I have a 400 Express Cruiser with twin 340 horse 7.4MPIs. It is a 1996 with 425 hours. I know Oil has changed in 20 years and I am interested in suggestions relative, using modern synthetics. Opinions? Thanks, Jon

Wholesale Marine Equipment. As found on the net, offers very attractive prices on Marine Equipment. They will want to ship via air Courier, Indra Pratama Express, at a fair price. I have ordered on line, several item that arrived as promised in the past from other overseas vendors. The company...